[Dsg-halla_gas] Prototype Gas Distribution System

[kagnanvo]

Hi Marc,

With Chuck help today, we moved the rack in the TEDF building where the 
Bigbite frame is located (where our GEM layer is installed). I don't 
really know the room number of the area but maybe Chuck could help me 
out here

Chuck also has prepared the gas cylinder to be used for the test and I 
believe everything is ready to go. So when you are available, we can go 
ahead with the installation.

I am not at JLab tomorrow so if you plan to work tomorrow, Chuck could 
help also. if not, I will be back at JLab on Thursday and we can plan 
accordingly

Please let me know

Best regards

Kondo


On 12/14/2020 12:09 PM, Marc Mcmullen wrote:
> Kondo,
>
> You are correct, the distribution rack is located in EEL 125, near 
> Chuck's gas bottles. They do need to be moved to the test location in 
> the TEDF.
>
> Please let me know, where that location is in the TEDF (room number).
>
> As far as calibrating, I believe you just want to connect your old 
> flow meters in-line to check if the flow values match.  You may need 
> to get with Jack (system owner) on that for those kind of questions.
>
> let me know if you have any questions or when the distribution panel 
> is moved and I'll make arrangements for the software start up.
>
> Marc
> ------------------------------------------------------------------------
> *From:* kagnanvo <kagnanvo at jlab.org>
> *Sent:* Monday, December 14, 2020 12:01 PM
> *To:* Marc Mcmullen <mcmullen at jlab.org>; Gnanvo, Kondo (kg6cq) 
> <kg6cq at virginia.edu>; dsg-halla_gas at jlab.org <dsg-halla_gas at jlab.org>
> *Cc:* nilanga at virginia.edu <nilanga at virginia.edu>
> *Subject:* Re: [Dsg-halla_gas] Prototype Gas Distribution System
>
> Hi again Marc,
>
> Just to clarify a few things once again. So right the rack is in 
> EEL125 and you want us to move it to TEDF right?
>
> I can see that with Chuck tomorrow then
>
> Then after that I will have to get in touch with you for setting the 
> raspberry pi and the associate software.
>
> We will have to also set up a mechanism to calibrate the gas flow 
> meter that you provide with the one we were using in EEL124 clean room.
>
> Can we install temporarily one of our flow meter on the panel to 
> perform this calibration?
>
> Bets regards
>
> Kondo
>
>
> On 12/14/2020 10:44 AM, Marc Mcmullen wrote:
>> Good Morning Kondo,
>>
>> I am just checking on how the installation of the UVA GEM is going. 
>> Please let me know when the Gas Distribution panel moves to the TEDF 
>> and provide me with the room location and I will make arrangements to 
>> connect the Raspberry Pi and start the gas flow readback software.
>>
>> Regards,
>> Marc
>> ------------------------------------------------------------------------
>> *From:* Marc Mcmullen <mcmullen at jlab.org> <mailto:mcmullen at jlab.org>
>> *Sent:* Wednesday, December 9, 2020 2:26 PM
>> *To:* Gnanvo, Kondo (kg6cq) <kg6cq at virginia.edu> 
>> <mailto:kg6cq at virginia.edu>; dsg-halla_gas at jlab.org 
>> <mailto:dsg-halla_gas at jlab.org> <dsg-halla_gas at jlab.org> 
>> <mailto:dsg-halla_gas at jlab.org>
>> *Cc:* nilanga at virginia.edu <mailto:nilanga at virginia.edu> 
>> <nilanga at virginia.edu> <mailto:nilanga at virginia.edu>
>> *Subject:* Re: Prototype Gas Distribution System
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-halla_gas/attachments/20201215/821859ca/attachment.html>