[Dsg-halla_magnets] Request for moving the SoLID magnet instrumentation racks

[Walt Akers]

For now, we should install them immediately adjacent to
the CLEO II magnet - as the other systems will all need to
be relocated in order to accomodate the assembly of that
magnet in the coming months.

Let me know when you want to walk over there and we'll
look at the space.

Walt

Pablo Campero Rojas wrote:
> Yes, racks will need to be powered and be operational (including 
> network access connection).
>
> --Pablo
> ------------------------------------------------------------------------
> *From:* Walt Akers <akers at jlab.org>
> *Sent:* Wednesday, September 8, 2021 3:30 PM
> *To:* Pablo Campero Rojas <campero at jlab.org>; 
> dsg-halla_magnets at jlab.org <dsg-halla_magnets at jlab.org>
> *Cc:* Patrizia Rossi <rossi at jlab.org>
> *Subject:* Re: Request for moving the SoLID magnet instrumentation racks
> I'm sure we can make this work. Do they need to be powered and 
> operational,
> or merely stored?
>
> Walt
>
> Pablo Campero Rojas wrote:
> > Hello Walt,
> >
> > Did you check our request to move the SoLID magnet instrumentation
> > racks from TEDF (room 1544) to the Test Lab high bay area?
> >
> >
> > Regards,
> > Pablo
> > ------------------------------------------------------------------------
> > *From:* Pablo Campero Rojas <campero at jlab.org>
> > *Sent:* Thursday, August 26, 2021 4:16 PM
> > *To:* Walt Akers <akers at jlab.org>; dsg-halla_magnets at jlab.org
> > <dsg-halla_magnets at jlab.org>
> > *Cc:* Patrizia Rossi <rossi at jlab.org>
> > *Subject:* Re: [Dsg-halla_magnets] Fw: SoLID Magnet wiring work
> > Hello Walt,
> >
> > For the space allocations, the approximate footprint required for the
> > two racks is of at least 9' X 6'.
> > We would like to have the racks moved to the high bay area by 8/31/2021.
> >
> > Regards,
> > Pablo
> >
> >
> > ------------------------------------------------------------------------
> > *From:* Dsg-halla_magnets <dsg-halla_magnets-bounces at jlab.org> on
> > behalf of Steven Lassiter <lassiter at jlab.org>
> > *Sent:* Thursday, August 26, 2021 3:36 PM
> > *To:* dsg-halla_magnets at jlab.org <dsg-halla_magnets at jlab.org>
> > *Cc:* Walt Akers <akers at jlab.org>
> > *Subject:* [Dsg-halla_magnets] Fw: SoLID Magnet wiring work
> > Also,moving the racks into the Test Lab high bay area needs to be run
> > by Walt Akers for space allocation.
> >
> > How much of foot print is required?
> >
> > Steven
> >
> >
> > ------------------------------------------------------------------------
> > *From:* Steven Lassiter <lassiter at jlab.org>
> > *Sent:* Thursday, August 26, 2021 3:31 PM
> > *To:* Pablo Campero Rojas <campero at jlab.org>
> > *Subject:* Re: [Dsg-halla_magnets] SoLID Magnet wiring work
> > Great News.
> >
> >  Hall C techs were slated to start work on the wiring but would have
> > to wait until the hall closes up early Sept.
> >
> >  1. Wiring should be completed by third week of Sept. This gives 4
> >     weeks to do the wiring and then hot check out can be carried out
> >     while the magnet is being moved and the CCR and current service
> >     turret assembled to the magnet.
> >  2. The racks are located in tedf room 1544. This is a private room
> >     with floor to ceiling walls and can accommodate two people at one
> >     time, if not more. The room is long. Face mask is all that is
> >     require as there is no need for people being closer than 6 feet
> >     for this work. One could wear gloves is so desired.
> >  3. The room is locked as the room contains spare parts for HallC. If
> >     it needs to be moved, the Hall C techs will have to do it and that
> >     could be delayed until the hall  closes.
> >  4.  Two to three people can work on the rack in its present location.
> >     Two people working on a rack at the time is about as much as one
> >     would want to have. the third person can be in the room cutting,
> >     stripping and attached ferrules to the ends of the cables prior to
> >     installing into the racks.
> >
> > thanks again
> > Steven
> >
> > ------------------------------------------------------------------------
> > *From:* Dsg-halla_magnets <dsg-halla_magnets-bounces at jlab.org> on
> > behalf of Pablo Campero Rojas <campero at jlab.org>
> > *Sent:* Thursday, August 26, 2021 2:48 PM
> > *To:* dsg-halla_magnets at jlab.org <dsg-halla_magnets at jlab.org>
> > *Cc:* Patrizia Rossi <rossi at jlab.org>
> > *Subject:* [Dsg-halla_magnets] SoLID Magnet wiring work
> >
> > Hello Steven,
> >
> >
> > Dr. Rossi approved that DSG works on the wiring of the SoLID magnet
> > instrumentation in the racks.
> >
> > DSG needs to schedule the wiring work so that our support for other
> > projects is not affected. Also, we'll need to follow all recommended
> > MEDCON 4 protocols and keep social distancing to minimize the risk of
> > exposure to COVID-19.
> >
> > Can you provide the answer to the questions below?
> >
> >  1. When does the racks’ wiring need to be completed?
> >  2. Where are the racks located?
> >  3. Is the access to the racks restricted?
> >  4. How many people will be around the rack in its present location?
> >
> >
> > DSG suggests moving the racks to the Test Lab high bay area so that
> > people are able to be socially distant.
> >
> > DSG would like cable spools to be moved by Hall A from the physics
> > storage next to racks prior to the start of work.
> >
> > Regards,
> >
> > Pablo
> >
> >
>