[Dsg-halla_magnets] SoLID magnet drawings

[Brian Eng]

I wasn't so interested in the connectors themselves, since they just seem like something Oxford got/did themselves, but rather the flange itself.

Mainly the OD, thickness, o-ring, and any bolt holes since pictures I've seen have way more than just the 3 for the connectors themselves.

________________________________
From: Whit Seay <wseay at jlab.org>
Sent: Thursday, June 9, 2022 11:35 AM
To: Brian Eng <beng at jlab.org>; Pablo Campero Rojas <campero at jlab.org>
Cc: dsg-halla_magnets at jlab.org <dsg-halla_magnets at jlab.org>
Subject: Re: [Dsg-halla_magnets] SoLID magnet drawings

Brian,

That is one of the dead ends I hit. We have no record of AJE 147.  It does not show up in the drawing list we were provided.  However, item 21 is shown on sheet 8 of that same drawing set with a corresponding part number that matches.  And it is the conical housing and provides no additional information related to the connectors.  See attached Sh 8.

My best guess is what we are looking for is one of items 73, 74 or 75.

Whit
________________________________
From: Brian Eng <beng at jlab.org>
Sent: Thursday, June 9, 2022 11:16 AM
To: Pablo Campero Rojas <campero at jlab.org>; Whit Seay <wseay at jlab.org>
Cc: dsg-halla_magnets at jlab.org <dsg-halla_magnets at jlab.org>
Subject: Re: [Dsg-halla_magnets] SoLID magnet drawings

Hi Whit,

Is there a drawing that has dimensions/information for the flange with the three connectors on it? It is part 21 from the table, which has "AJE 0147 Machined Items" as the header, maybe it's in that drawing?

Thanks
________________________________
From: Dsg-halla_magnets <dsg-halla_magnets-bounces at jlab.org> on behalf of Pablo Campero Rojas <campero at jlab.org>
Sent: Wednesday, June 8, 2022 10:49 AM
To: Whit Seay <wseay at jlab.org>
Cc: dsg-halla_magnets at jlab.org <dsg-halla_magnets at jlab.org>
Subject: Re: [Dsg-halla_magnets] SoLID magnet drawings

Hello Whit,

Thanks you for sharing the information.

With regards to the disconnection of the wiring for these pin connectors, I'll pass it to DSG management and we'll be back with you.


--Pablo
________________________________
From: Whit Seay <wseay at jlab.org>
Sent: Tuesday, June 7, 2022 9:40 AM
To: Pablo Campero Rojas <campero at jlab.org>
Cc: Steven Lassiter <lassiter at jlab.org>
Subject: Re: SoLID magnet drawings

Pablo,
I have sifted through all of the drawings twice and search the manual for more leads and I cannot find any additional information other than what you see below.  Those are not likely part numbers.  In fact I'm not sure that is the actual connectors listed but just the parts they fit in.  I cannot find any reference to the connector.  Other than taking one a part in hopes of getting part numbers, I do not know what else to do.

Are you guys going to help with the disconnecting the wiring for these pin connectors so we can clean the inside of the turret?

Sorry that I couldn't be of more help,

Whit

[cid:f6e8fcdc-df34-439d-9d6a-dfa08eba452b]
________________________________
From: Pablo Campero Rojas <campero at jlab.org>
Sent: Wednesday, May 25, 2022 12:11 PM
To: Whit Seay <wseay at jlab.org>
Subject: SoLID magnet drawings

Hello Whit,

Do you have more drawings than the ones provided last time for the instrumentation (AJE 0145, AJE0141).

We're looking for drawings that could have information about the turret instrumentation connectors since we're trying to see if these are still available or if there is any replacement in case they break while the pins get unbent.


Thanks,
Pablo
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-halla_solid/attachments/20220609/67d211db/attachment-0002.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image.png
Type: image/png
Size: 82227 bytes
Desc: image.png
URL: <https://mailman.jlab.org/pipermail/dsg-halla_solid/attachments/20220609/67d211db/attachment-0002.png>