<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=us-ascii">
<style type="text/css" style="display:none;"> P {margin-top:0;margin-bottom:0;} </style>
</head>
<body dir="ltr">
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
Hi Alls<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
Updates:</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
The radial strain gauges are now all connected and roughly calibrated. They seem to be working okay now.
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
The axial strain gauges will not be used during the Test Lab cool down and low current testing. The axial gauges would be attached to the bolts going through the end yokes and but the yoke is not being used. We could consider masking or turning off their on
the HMI display or at least their red flashing indicators.</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
The CCR's and HX's PT102 temperature sensors have been roughly calibrated to be at 295K for room temperature. The room temperature resistance offsets have been used for the 77K data point as well.
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
The CCR Diode temperature sensors have been front end calibrated to read 295K as well. The front end calibration used a sensor offset of -0.033V for each diode but the display only shows -0.03. the third decimal is being used and is importation just not being
shown. This is one reason I prefer to do fine calibration within the logic program, but for the temperature sensors front end calibrations will suffice for now.</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
The Liquid levels inputs have been changed from, 4-20mA to 0-10V signals. A8:ch8 for Helium and A8:ch9 for the LN2. Fine tuning will occur once the probes are cold and when filling can occur.<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
The wide range vacuum gauge arrived and is in the cabinet. The 4 wire cable (#405-03) for the vacuum gauge needs to be installed and connected to the unit.<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
Thanks for the efforts<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
Steven<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div id="appendonsend"></div>
<hr style="display:inline-block;width:98%" tabindex="-1">
<div id="divRplyFwdMsg" dir="ltr"><font face="Calibri, sans-serif" style="font-size:11pt" color="#000000"><b>From:</b> Dsg-halla_magnets <dsg-halla_magnets-bounces@jlab.org> on behalf of Brian Eng <beng@jlab.org><br>
<b>Sent:</b> Wednesday, August 3, 2022 10:42 AM<br>
<b>To:</b> dsg-halla_magnets@jlab.org <dsg-halla_magnets@jlab.org><br>
<b>Subject:</b> [Dsg-halla_magnets] 8/3 Meeting at 11</font>
<div> </div>
</div>
<style type="text/css" style="display:none">
<!--
p
{margin-top:0;
margin-bottom:0}
-->
</style>
<div dir="ltr">
<div style="font-family:Calibri,Arial,Helvetica,sans-serif; font-size:12pt; color:rgb(0,0,0)">
Just talked with Steven this morning, this meeting will be cancelled so that we can focus on rewiring the rack.</div>
</div>
</body>
</html>