Does someone know what caused the leak in the first place 15 months ago?
Was a request made to fix it?
If yes, to whom?






----- Original Message -----
From: Aune Stephan <stephan.aune@cea.fr>
To: Matthew Marchlik <marchlik@jlab.org>, Brian Eng <beng@jlab.org>
Cc: Volker Burkert <burkert@jlab.org>, SABATIE Franck <Franck.Sabatie@cea.fr>, Bob Miller <rmiller@jlab.org>, dsg-ft@jlab.org, dsg-mvt@jlab.org
Sent: Wed, 07 Jun 2017 13:24:32 -0400 (EDT)
Subject: Re: [Dsg-ft] [Dsg-mvt] MVT mixing system - Lite Version

Hi
thank you Brian, good job

we have measure no leak (under 3.6 10E-4 l/h) on it

perfect

Stephan
________________________________________
De : Matthew Marchlik [marchlik@jlab.org]
Envoyé : mercredi 7 juin 2017 19:13
À : Brian Eng
Cc : Aune Stephan; Volker Burkert; George Jacobs; SABATIE Franck; Bob Miller; dsg-mvt@jlab.org; dsg-ft@jlab.org
Objet : Re: [Dsg-mvt] MVT mixing system - Lite Version

Brian,

I will go out and take a look at the installation.

Opening the regulator to it's max of 15 psi and performing the leak test with the Ar detector will suffice. Please let me know after leak check is performed successfully.

Matt

----- Original Message -----
From: "Brian Eng" <beng@jlab.org>
To: "Aune Stephan" <stephan.aune@cea.fr>
Cc: "Volker Burkert" <burkert@jlab.org>, "George Jacobs" <jacobsg@jlab.org>, "SABATIE Franck" <Franck.Sabatie@cea.fr>, "Matthew Marchlik" <marchlik@jlab.org>, "Bob Miller" <rmiller@jlab.org>, dsg-mvt@jlab.org, dsg-ft@jlab.org
Sent: Wednesday, June 7, 2017 1:01:10 PM
Subject: Re: [Dsg-mvt] MVT mixing system - Lite Version

Hi Stephan,

Since we couldn't find a suitable replacement relief valve on-site we've replaced the bad one with 2 identical ones in parallel per Matt's approval.

We have a DSG meeting after lunch, but after you guys use your Argon leak checker let us know if there's any problems with the current setup.

Matt, I don't know if you need to do anything prior to them flowing gas again?

Thanks
--
Brian Eng
Detector Support Group
757-269-6018

> On Jun 7, 2017, at 10:37 AM, Aune Stephan <stephan.aune@cea.fr> wrote:
>
> Hi
> An answer on the need for the “lite system”: it will work fine for MVT.
>
> Knowing a Pure isobutene bottle will last more than a 3 month run, check on the remaining weight  on manual scale (no pressure measurement possible) will have to be done ~ monthly. And the bottle could be exchanged between run.
>
> We have another issue to solve here and now.
>
> Yesterday morning we saw that the Argon bottle we use in Eel was empty. We have been using for our test less than 10 l/h since we arrived (we qualify our detector when leak is under 0.05 l/h !) , and only day time. Thus less than 500 l have been used but the bottle (10 000 l) is already empty.
>
> We, Saclay team, found the leak (~ 50 l/h) this morning. It is outside on the pressure release valve. The same leak we had found 15 months ago on MVT B2. The Eel gas system was not done properly and not tested either, which is surprising considering the amount of safety paperwork we on the other end have to go through to turn anything on.
>
> Bob gave instruction to solve it. I do not want to waste isobutene premix with such a leak.
>
> Stephan

_______________________________________________
Dsg-ft mailing list
Dsg-ft@jlab.org
https://mailman.jlab.org/mailman/listinfo/dsg-ft