[Dsg-hallb_magnets] Solenoid- PLC software comparators

[Pablo Campero]

Hello Wesley, Renuka 

I changed the tag names in the PLC code as we agreed from C1 to COMP1, C2 to COMP2, etc for the ten software comparators, and also I updated the spreadsheet on the M:Drive. 

Regards 
Pablo. 


From: "Wesley Moore" <wmoore at jlab.org> 
To: "Renuka Rajput-Ghoshal" <renuka at jlab.org> 
Cc: "Pablo Campero" <campero at jlab.org>, "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org> 
Sent: Friday, December 2, 2016 1:36:48 PM 
Subject: Re: [Dsg-hallb_magnets] Solenoid- PLC software comparators 

Renuka, 

I thought you had a good point. I was just relaying how the convention came about. C1 -> COMP1 is little effort for me and should be no problem on the PLC side. 

Wesley 

----- Original Message ----- 
> From: "Renuka Rajput-Ghoshal" <renuka at jlab.org> 
> To: "Wesley Moore" <wmoore at jlab.org> 
> Cc: "Pablo Campero" <campero at jlab.org>, "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org> 
> Sent: Friday, December 2, 2016 1:31:13 PM 
> Subject: Re: [Dsg-hallb_magnets] Solenoid- PLC software comparators 

> Hello Wesley, 
> In the Torus magnets coils are referred as Coil A, B etc. 
> But for solenoid the coils are referred as C1, C2....C5. 
> That's why I think it could be confusing to use C1, C2 for comparator voltages! 
> I would prefer something different (like as I mentioned in my previous email 
> COMP1, COMP2 etc.) 
> 
> Please let me know if it adds to too much of work and confusion at your end. 
> 
> Thanks 
> Renuka 
> 
> 
> ----- Original Message ----- 
> From: "Wesley Moore" <wmoore at jlab.org> 
> To: "Renuka Rajput-Ghoshal" <renuka at jlab.org> 
> Cc: "Pablo Campero" <campero at jlab.org>, "dsg-hallb magnets" 
> <dsg-hallb_magnets at jlab.org> 
> Sent: Friday, December 2, 2016 11:41:23 AM 
> Subject: Re: [Dsg-hallb_magnets] Solenoid- PLC software comparators 
> 
> VT#, V#, and C# match the Torus convention. 
> 
> Wesley 
> 
>> On Dec 2, 2016, at 10:32 AM, Renuka Rajput-Ghoshal <renuka at jlab.org> wrote: 
>> 
>> Hello Pablo, 
>> The description and calculations looks good to me, but the PLC tag for 
>> comparators (C1, C2 etc.) are confusing! Normally C is used for coil, but these 
>> are not the coils! 
>> Could you suggest some other name (may be COMP1 etc.). 
>> 
>> Thanks 
>> Renuka 
>> 
>> 
>> ----- Original Message ----- 
>> From: "Pablo Campero" <campero at jlab.org> 
>> To: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org> 
>> Sent: Thursday, December 1, 2016 5:00:46 PM 
>> Subject: [Dsg-hallb_magnets] Solenoid- PLC software comparators 
>> 
>> Hello Wesley, 
>> 
>> Attached table with the PLC tag name for the Solenoid software comparators and 
>> voltages. 
>> You can also find this spreadsheet in the M Drive, the path is 
>> M:\hallb_eng\CLAS12\Magnets\Solenoid\Controls and Wiring Solenoid PLC Software 
>> Comparators 
>> 
>> Renuka, 
>> 
>> Let me know if you have any correction in the attached table, I assigned the 
>> voltage (V1 to V15 ) and comparators (C1 to C10) based on your "Hall-B Solenoid 
>> Quench Detector Channel Assigment and Voltage Limits QD and Software" spread 
>> sheet. 
>> 
>> Thanks 
>> Pablo Campero 
>> Detector Support Group. 
>> 
>> 
>> 
>> _______________________________________________ 
>> Dsg-hallb_magnets mailing list 
>> Dsg-hallb_magnets at jlab.org 
>> https://mailman.jlab.org/mailman/listinfo/dsg-hallb_magnets 
>> _______________________________________________ 
>> Dsg-hallb_magnets mailing list 
>> Dsg-hallb_magnets at jlab.org 
> > https://mailman.jlab.org/mailman/listinfo/dsg-hallb_magnets 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hallb_magnets/attachments/20161207/9515d0d9/attachment.html>