[Dsg-hallb_magnets] TR817A2 at 325 K, LV cRIO restarted.

[Ruben Fair]

Thank you Tyler

Can you also add the LV chassis number and also the LV chassis D-type connector label?

Cheers

Ruben

> On Apr 19, 2017, at 5:20 PM, Glenn Young <gyoung at jlab.org> wrote:
> 
> Dear Tyler,
> Excellent. Can you tell me how many total Cernox there are?   A quick glance at your table suggests the occurrence is random with respect to the device number - i.e. it does not point to the sensor in particular, except for perhaps TF817B8.
> Regards, Glenn
> 
> ----- Original Message -----
> From: "Tyler Lemon" <tlemon at jlab.org>
> To: "Glenn Young" <gyoung at jlab.org>
> Cc: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org>, "Ramakrishna Bachimanchi" <bachiman at jlab.org>
> Sent: Wednesday, April 19, 2017 5:15:36 PM
> Subject: Re: [Dsg-hallb_magnets] TR817A2 at 325 K, LV cRIO restarted.
> 
> Hello Glenn, 
> 
> The table attached shows since January, 1 2017, which Cerenoxes have had the error, how many times a Cerenox has had the error, and the dates of the error. 
> 
> Best regards, 
> Tyler 
> 
> 
> 
> 
> 
> From: "Glenn Young" <gyoung at jlab.org> 
> To: "Tyler Lemon" <tlemon at jlab.org> 
> Cc: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org>, "Ramakrishna Bachimanchi" <bachiman at jlab.org> 
> Sent: Wednesday, April 19, 2017 4:47:55 PM 
> Subject: Re: [Dsg-hallb_magnets] TR817A2 at 325 K, LV cRIO restarted. 
> 
> Dear Tyler, 
> Do we have statistics of which Cernox exhibit the 325k error? I.e. is it randomly distributed or are there a few specific ones that are most like to have the problem? 
> Thanks, Glenn 
> 
> ----- Original Message ----- 
> From: "Tyler Lemon" <tlemon at jlab.org> 
> To: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org>, "Ramakrishna Bachimanchi" <bachiman at jlab.org> 
> Sent: Wednesday, April 19, 2017 4:10:47 PM 
> Subject: [Dsg-hallb_magnets] TR817A2 at 325 K, LV cRIO restarted. 
> 
> Hello, 
> 
> TR817A2 was at 325 K this afternoon. The Torus LV cRIO was reset and the Cerenox now reads 4.75 K. 
> 
> I did not get a screen shot of the raw data from the error. I initially connected to the LV cRIO from a different PC than usual. This PC did not have the required LabVIEW packages installed, causing an error when connecting to the cRIO. This error stopped the program. After moving to the PC normally used for Hall B LabVIEW, the program was successfully restarted following the normal restart procedure. 
> 
> Best regards, 
> Tyler 
> 
> _______________________________________________ 
> Dsg-hallb_magnets mailing list 
> Dsg-hallb_magnets at jlab.org 
> https://mailman.jlab.org/mailman/listinfo/dsg-hallb_magnets
> _______________________________________________
> Dsg-hallb_magnets mailing list
> Dsg-hallb_magnets at jlab.org
> https://mailman.jlab.org/mailman/listinfo/dsg-hallb_magnets