[Dsg-hallb_magnets] Torus TR8122A at 325 K fixed via LV cRIO restart

[Nicholas Sandoval]

Yes, thanks for the reminder.  I now recall we went through that process I will double check and make sure that we can use that account so that the program/source is all readily available through a desktop link.

Thanks again,

Nick

----- Original Message -----
From: "Tyler Lemon" <tlemon at jlab.org>
To: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org>
Sent: Wednesday, February 1, 2017 9:20:29 AM
Subject: Re: [Dsg-hallb_magnets] Torus TR8122A at 325 K fixed via LV cRIO restart

Hi Nick, 

I'll add the remote log in instructions. 

In December after the clas12magsupport group user password expired and was updated, computer center's help reply was that the account then had to be reactivated. Maybe they didn't get around to reactivating the account? 

Tyler 


From: "Nicholas Sandoval" <sandoval at jlab.org> 
To: "Tyler Lemon" <tlemon at jlab.org> 
Sent: Wednesday, February 1, 2017 9:10:24 AM 
Subject: Re: [Dsg-hallb_magnets] Torus TR8122A at 325 K fixed via LV cRIO restart 

Great Thank you. 

I will be leaving the PLC laptop in the counting house with a connection to the Hall B subnet. Perhaps you can include a few steps regarding using remote desktop to the clas12magplc. I just tried and it seems the account has changed? 

Thanks, 

Nick 



----- Original Message ----- 
From: "Tyler Lemon" <tlemon at jlab.org> 
To: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org> 
Sent: Wednesday, February 1, 2017 9:01:52 AM 
Subject: Re: [Dsg-hallb_magnets] Torus TR8122A at 325 K fixed via LV cRIO restart 

Hi Nick, 

Attached is a procedure for restarting the Torus LV cRIO. Noted at the top of the procedure is that a Hall B subnet PC with LabVIEW 2016 and the LabVIEW program are needed. 

An alternate procedure would be just rebooting the LV cRIO. This does not require any interaction with the LabVIEW program but the downside of just rebooting the cRIO is that it would take a few minutes to fully go back online. If this option would be preferred, I can change the procedure. 

Best regards, 
Tyler 



From: "Nicholas Sandoval" <sandoval at jlab.org> 
To: "Tyler Lemon" <tlemon at jlab.org> 
Cc: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org> 
Sent: Tuesday, January 31, 2017 9:40:46 AM 
Subject: Re: [Dsg-hallb_magnets] Torus TR8122A at 325 K fixed via LV cRIO restart 

Hi Tyler, 

Could you please provide instructions for the Hall B counting house/on-call to be able to restart the Torus LV cRIO. If TR8122A indicated 325K during the KPP's it would bring the magnet down. They would not be able to clear it until the reset. 

Best REgards, 
Nick 

----- Original Message ----- 
From: "Tyler Lemon" <tlemon at jlab.org> 
To: "dsg-hallb magnets" <dsg-hallb_magnets at jlab.org> 
Sent: Monday, January 30, 2017 11:40:06 AM 
Subject: [Dsg-hallb_magnets] Torus TR8122A at 325 K fixed via LV cRIO restart 

Hello, 

I noticed TR8122A for the Torus chimney splice was reading 325 K. This seems to have been the same Cerenox LV excitation error that happened twice last week. After restarting the Torus LV cRIO, TR8122A now reads ~6.3 K. 

Tyler 

_______________________________________________ 
Dsg-hallb_magnets mailing list 
Dsg-hallb_magnets at jlab.org 
https://mailman.jlab.org/mailman/listinfo/dsg-hallb_magnets 


_______________________________________________ 
Dsg-hallb_magnets mailing list 
Dsg-hallb_magnets at jlab.org 
https://mailman.jlab.org/mailman/listinfo/dsg-hallb_magnets 

_______________________________________________
Dsg-hallb_magnets mailing list
Dsg-hallb_magnets at jlab.org
https://mailman.jlab.org/mailman/listinfo/dsg-hallb_magnets