<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1">
<style type="text/css" style="display:none;"> P {margin-top:0;margin-bottom:0;} </style>
</head>
<body dir="ltr">
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
MFC is working again (needed to be reinitialized). Minimum flow is 1.5 lpm, any lower set point will flow zero.</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
SB1 H1 is reading bad due to the gray cable between the board on the patch panel and the V450, I wasn't sure where the spares are but I suspect changing that out might fix that reading.</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
SB3 and SB6 are reading the same from the V450 and the cRIO, not sure what else I can do there. Disconnecting the cRIO makes no difference to the readings.</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
I tried repairing the SB4 cable, before remembering that it's actually bad on the HTSB itself (<a href="https://logbooks.jlab.org/entry/3434654" id="LPlnk646141">https://logbooks.jlab.org/entry/3434654</a>), so I removed the same pin but on the other side of
the connector as I couldn't find the correct extraction tool.</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
<br>
</div>
<div style="font-family: Calibri, Arial, Helvetica, sans-serif; font-size: 12pt; color: rgb(0, 0, 0);">
R2 M13 will need to wait as I couldn't find the crimper for that connector.</div>
<div>
<div id="appendonsend"></div>
<div style="font-family:Calibri,Arial,Helvetica,sans-serif; font-size:12pt; color:rgb(0,0,0)">
<br>
</div>
<hr tabindex="-1" style="display:inline-block; width:98%">
<div id="divRplyFwdMsg" dir="ltr"><font face="Calibri, sans-serif" color="#000000" style="font-size:11pt"><b>From:</b> Yuri Gotra <gotra@jlab.org><br>
<b>Sent:</b> Wednesday, May 5, 2021 6:23 PM<br>
<b>To:</b> Brian Eng <beng@jlab.org><br>
<b>Cc:</b> Rafayel Paremuzyan <rafopar@jlab.org><br>
<b>Subject:</b> SVT slow controls issues</font>
<div> </div>
</div>
<div>
<p><font size="+1">Brian,</font></p>
<p><font size="+1">We left SVT open at 20 C.</font></p>
<p><font size="+1">Issues to be resolved:</font></p>
<p><font size="+1">- MFC shows no flow. We set it to 0 for now and closed the rotameter</font></p>
<p><font size="+1">- ambient sensors need to be tested, SB3 doesn't work</font></p>
<p><font size="+1">- R2S13 temperature sensor cable has broken wire. It would be great to test all hybrid temperature sensor cable connections which can be done by turning one by one LV for a short time to see if the temperature reading is ok.</font></p>
<p><font size="+1">Thank you</font><br>
</p>
</div>
</div>
</body>
</html>