[Dsg-hallc_controls] Status of SHMS PLC upgrades

[Amrit Yegneswaran]

well done guys, 
have a great weekend. 



From: "Brian Eng" <beng at jlab.org> 
To: "Pablo Campero" <campero at jlab.org> 
Cc: "rossi patrizia" <rossi at jlab.org>, "dsg-hallc controls" <dsg-hallc_controls at jlab.org> 
Sent: Friday, July 13, 2018 5:34:52 PM 
Subject: Re: [Dsg-hallc_controls] Status of SHMS PLC upgrades 

Logbook entry of the work: https://logbooks.jlab.org/entry/3581082 

----- Original Message ----- 
> From: "Pablo Campero" <campero at jlab.org> 
> To: "dsg-hallc controls" <dsg-hallc_controls at jlab.org> 
> Cc: "rossi patrizia" <rossi at jlab.org> 
> Sent: Friday, July 13, 2018 5:15:27 PM 
> Subject: Re: [Dsg-hallc_controls] Status of SHMS PLC upgrades 

> Hello, 
> 
> Today DSG continued with the task to upgrade SHMS PLC to version 20. 
> Redundancy synchronization was re-enabled, Primary and Secondary PLC chassis are 
> communicating and running without problems. 
> 
> The swapping of the ControlNet modules (CN2B) by Ethenet modules in the Q1 and 
> HX PLC chassis was performed as follows: 
> 
> 
> * ACD PLC program V20 modified to add two Ethernet modules. 
> * Firmware version for Ethernet modules were upgraded : Q1- EN2T to V5.8 and 
> HX-ENBT to V 6.6. 
> * Al I/O modules for Q1 and HX PLC chassis configured in the ACD PLC program 
> with the same configurations, names, and engineering units. 
> * Set up both Ethernet modules in the ACD project file under existing Ethernet 
> network running in the Prymary/ Secondary PLC chassis. 
> 
> After all upgrades completed and the downloading of ACD file on the SHMS PLC v20 
> on the PLC controller, all RUN with no problems and without errors found. A 
> copy of the SHMS v20 ACD file was gave to Mike to run on the "Skylla7" 
> computer. 
> Regard, 
> Pablo 
> 
> 
> 
> 
> 
> 
> 
> 
> 
> Redundancy configuration 
> 
> From: "Brian Eng" <beng at jlab.org> 
> To: "Pablo Campero" <campero at jlab.org> 
> Cc: "dsg-hallc controls" <dsg-hallc_controls at jlab.org>, "rossi patrizia" 
> <rossi at jlab.org> 
> Sent: Friday, July 13, 2018 10:03:46 AM 
> Subject: Re: [Dsg-hallc_controls] Status of SHMS PLC upgrades 
> 
> We're headed to Hall C to switch the valves from PLC to manual control prior to 
> starting work on trying to get the redundancy back up and running. 
> 
> ----- Original Message ----- 
>> From: "Pablo Campero" <campero at jlab.org> 
>> To: "dsg-hallc controls" <dsg-hallc_controls at jlab.org> 
>> Cc: "rossi patrizia" <rossi at jlab.org> 
>> Sent: Thursday, July 12, 2018 7:32:33 PM 
>> Subject: [Dsg-hallc_controls] Status of SHMS PLC upgrades 
>> 
>> Tomorrow morning will continue with the setup of the redundancy synchronization 
>> and firmware upgrades for the remain communication modules (ENBT,EN2T,CN2B) in 
>> remote PLC chassis . Then the plan is continue with the swapping of Controlnet 
>> modules by Ethernet modules (Chassis Q1 and HX) if there is no problems with 
>> the redundancy synchronization. 
> 
> _______________________________________________ 
> Dsg-hallc_controls mailing list 
> Dsg-hallc_controls at jlab.org 
> https://mailman.jlab.org/mailman/listinfo/dsg-hallc_controls 
_______________________________________________ 
Dsg-hallc_controls mailing list 
Dsg-hallc_controls at jlab.org 
https://mailman.jlab.org/mailman/listinfo/dsg-hallc_controls 
G 
M 
T 
		
		
	
	
	
	
Text-to-speech function is limited to 200 characters 
	
	Options : History : Feedback : Donate 	Close 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hallc_controls/attachments/20180713/4f3afd88/attachment.html>