[dsg-hdice] temporary RF generator

Fri Nov 16 08:41:20 EST 2018

Hi Xiangdong, 

We fixed the FRS program. It is ready for testing. 

Regards, 
Amanda 

From: "Xiangdong Wei" <xwei at jlab.org> 
To: "Amanda Hoebel" <amandah at jlab.org> 
Cc: dsg-hdice at jlab.org 
Sent: Thursday, November 15, 2018 8:02:57 PM 
Subject: Re: [dsg-hdice] temporary RF generator 

Hi Amanda, 

Thank you for installing the RF generator, I appreciate it. 

Now, would you please tune the FRS program as well? The error message is shown in the attached picture. 

Thanks, 

Xiangdong 

Xiangdong Wei 

x-5266 

----- Original Message ----- 
From: Amanda Hoebel <amandah at jlab.org> 
To: dsg-hdice at jlab.org 
Sent: Thu, 15 Nov 2018 15:06:47 -0500 (EST) 
Subject: Re: [dsg-hdice] temporary RF generator 

Hi Xiangdong, 

Mindy, Mary Ann, and I installed the RF generator and set it up to run in the NMR program. It is now ready for you to test. 

Also, we had to restart the computer to restart the ports. We tested the program with my login and after verifying the setup, we logged back out. 

Regards, 
Amanda 

From: "Xiangdong Wei" <xwei at jlab.org> 
To: "Amanda Hoebel" <amandah at jlab.org> 
Cc: dsg-hdice at jlab.org 
Sent: Thursday, November 15, 2018 12:28:17 PM 
Subject: Re: [dsg-hdice] temporary RF generator 

Hi Amanda, 

The loaner rf generator is at the shipping & receiving right now, I'll take it to the HDice lab before 2pm. I'll be in the meeting room this afternoon, but can be in the lab if needed. I'm on the Hall-B shift at the counting house between 7am and 3pm from Friday to Monday, the earliest time which I can start testing the new generator would be after 3pm tomorrow. 

Thanks, 

Xiangdong 

Xiangdong Wei 

x-5266 

From: "Amanda Hoebel" <amandah at jlab.org> 
To: dsg-hdice at jlab.org 
Sent: Tuesday, November 13, 2018 2:22:59 PM 
Subject: Re: [dsg-hdice] temporary RF generator 

Hi Xiangdong, 

We will help install the loaner RF generator in Rack 1. Let us know when it arrives. 

Regards, 
Amanda 

From: "Xiangdong Wei" <xwei at jlab.org> 
To: "dsg-hdice" <dsg-hdice at jlab.org> 
Sent: Tuesday, November 13, 2018 2:01:31 PM 
Subject: [dsg-hdice] temporary RF generator 

Hi Amanda, 

In order to avoid the delay on replacing the broken rf generator, Rohde & Schwarz located a loaner unit for us to use until the new one shows up (Please see the forwarded email below for details). When it shows up, could you find time helping me to install it on the Rack 1? Since we are using the SMA100A on the Rack 2 now, it might be as easy as plug & play. 

Thanks, 

Xiangdong 

Xiangdong Wei 

x-5266 

From: "Dale Simmonds" <Dale.Simmonds at rsa.rohde-schwarz.com> 
To: "Xiangdong Wei" <xwei at jlab.org> 
Sent: Tuesday, November 13, 2018 8:37:35 AM 
Subject: RE: Re: Thanks for Rohde & Schwarz SMB100A signal generator interest ....would you be available to meet next Wed. 11/7 or Thurs 11/8? 

Thanks Xiangdong for the additional clarification information below. 

I am hoping that a temporary loaner SMA100A might work for you and your software group. 

Our demo equipment group has approved loaning Jefferson Lab a SMA100A Serial Number 103430 until your new purchased 
SMB100A comes in. 

The SMA100A loaner can be shipped to you immediately to arrive within a few days if you can confirm the exact mailing address to make sure it finds its way to you within Jefferson Lab. 

The SMA100A loaner unit has these hardware –Bxxx options installed SMA-B103L, SMA-B22, SMA-B29 as described below. 

And if certain software options are needed, I should be able to get 30 day no cost evaluations enabled for you by Key Code. 

Product: SMA-B103 

Part Number: 1405.0209.02 

Description: Option: Frequency range 9kHz to 3GHz with electronic attenuator. 

Product: SMA-B22 

Part Number: 1405.1805.02 

Description: Option: Enhanced phase noise performance and FM/PHIM modulator. SMA-B10x required (factory fit) 

Product: SMA-B29 

Part Number: 1400.2503.02 

Description: Option: Clock Synthesizer 

Regards & let me know if this path might help, while I still press for expedited delivery of your order. 

Dale 

Dale Simmonds 

Account Manager - SoVA 

Rohde & Schwarz USA, Inc. 

Office: 540-872-3159 

Mobile: 443-253-2223 

E-Mail: Dale.Simmonds at rsa.rohde-schwarz.com 

Website: http://www.rohde-schwarz.com/ 

From: Xiangdong Wei <xwei at jlab.org> 

Sent: Monday, November 12, 2018 2:52 PM 
To: Simmonds Dale 5USED <Dale.Simmonds at rsa.rohde-schwarz.com> 
Subject: *EXT* Re: Thanks for Rohde & Schwarz SMB100A signal generator interest ....would you be available to meet next Wed. 11/7 or Thurs 11/8? 

Hi Dale, 

Thank you for look into this case. No, it's not for replacing SMA 100A on the left side rack, but for the really old SMY01 on the right side rack. (I have 2 NMR Racks side by side but only one functional signal 
generator (SMA100A) at this moment. I rushed to order the new unit in September just to replace the dead SMY01. 

The loaner option sounds good. Please let me check with our software people to see when they can migrate the software and get back to you. 

Thank you very for your help. 

Best regards, 

Xiangdong 

Xiangdong Wei, Ph. D. 

Staff Scientist 

B-116 CEBAF Center 

Jefferson Lab 

12000 Jefferson Ave. 

Newport News, VA 23606, USA 

(757) 269-5266 

From: "Dale Simmonds" < Dale.Simmonds at rsa.rohde-schwarz.com > 
To: "Xiangdong Wei" < xwei at jlab.org > 
Sent: Monday, November 12, 2018 2:13:52 PM 
Subject: RE: Re: Thanks for Rohde & Schwarz SMB100A signal generator interest ....would you be available to meet next Wed. 11/7 or Thurs 11/8? 

Hi Xiangdong, 

I am looking into this for you within R&S & TestEquity. 

Is it correct that the SMB100A sign gen you ordered is actually to replace the older SMA100A that you showed me last week, which has stopped working? 

If that is correct I see within our used equipment group (which tries to sell former customer demonstration equipment) has a few of the older SMA100A’s they are trying to sell. 

…..so I am wondering if perhaps they could loan one to me (and to you) to use, while you wait for your SMB100A to be delivered. 

If I could arrange something like that, would this help? 

Regards & glad you reached out to me on this. 

Dale 

Dale Simmonds 

Account Manager - SoVA 

Rohde & Schwarz USA, Inc. 

Office: 540-872-3159 

Mobile: 443-253-2223 

E-Mail: Dale.Simmonds at rsa.rohde-schwarz.com 

Website: http://www.rohde-schwarz.com/ 

From: Xiangdong Wei < xwei at jlab.org > 

Sent: Monday, November 12, 2018 12:59 PM 
To: Simmonds Dale 5USED < Dale.Simmonds at rsa.rohde-schwarz.com > 
Subject: *EXT* Re: Thanks for Rohde & Schwarz SMB100A signal generator interest ....would you be available to meet next Wed. 11/7 or Thurs 11/8? 

Hi Dale, 

Thank you very much for meeting me in my lab last week. 

This morning I just learned that the delivery date for my new RF generator will be delayed for 7 weeks (The original delivery date was 10/31 when ordered, 
but now is 12/-3!). Rohde & Schwarz didn't give the TestEquity.com any explanation for the delay for order# 
3500096691 (PO 301752). Could you do anything to speed up the process? As I mentioned to you last week, we are waiting for the RF generator to replace a broken one so we can finish 
the experiment on time. 

Thank you very much for your time and help. 

Best regards, 

Xiangdong 

Xiangdong Wei, Ph. D. 

Staff Scientist 

B-116 CEBAF Center 

Jefferson Lab 

12000 Jefferson Ave. 

Newport News, VA 23606, USA 

(757) 269-5266 

_______________________________________________ 
dsg-hdice mailing list 
dsg-hdice at jlab.org 
https://mailman.jlab.org/mailman/listinfo/dsg-hdice 

_______________________________________________ 
dsg-hdice mailing list 
dsg-hdice at jlab.org 
https://mailman.jlab.org/mailman/listinfo/dsg-hdice 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hdice/attachments/20181116/9f109269/attachment-0002.html>