[dsg-hdice] fsNMR front panel screenshot

[Tyler Lemon]

Xiangdong and Mike,

Since the whole library would be needed, it would be better if one of you could install the VIs in HDICENMR2 to make sure all the necessary VIs are there.

Afterwards, if necessary, I can check it to make sure the communication addresses for the power supplies are correct.

-Tyler

________________________________
From: Michael Lowry <mlowry at jlab.org>
Sent: Thursday, August 27, 2020 3:48:43 PM
To: Xiangdong Wei <xwei at jlab.org>; Tyler Lemon <tlemon at jlab.org>; dsg-hdice at jlab.org <dsg-hdice at jlab.org>
Subject: Re: fsNMR front panel screenshot

You need the full Oxford directory since the Oxford IPS VI calls many others.  --  Mike


________________________________
From: dsg-hdice <dsg-hdice-bounces at jlab.org> on behalf of Xiangdong Wei <xwei at jlab.org>
Sent: Thursday, August 27, 2020 2:34 PM
To: Tyler Lemon <tlemon at jlab.org>; dsg-hdice at jlab.org <dsg-hdice at jlab.org>
Subject: Re: [dsg-hdice] fsNMR front panel screenshot

Hi Tyler,

Thank you. I'll resume the fsNMR test now.

Another issue related to this rack during UITF runs just came out:

I just realized that since NMR Rack 2 will be operated inside the locked-up UITF during the eHD tests, so I can only run the Oxford power supply remotely through the mirror PC. We must install a full functioned VI for Oxford IPS on the Rack 2 PC to achieve the goal, I think. We have an original Oxford VI for the IPS on our dilution refrigerator controlling the 15 Tesla magnet, which can be installed on the Rack 2 PC without a big effort. Do you have a copy of the VI? If you like, to save time, we can install and test the VI first, so you can you can add it in the project after that. The IPS VI should be operated independently from fsNMR run, but should be in the same project to avoid interference, I think.

Please let know your opinion, and proposal.

Thanks,

Xiangdong
________________________________
From: Tyler Lemon <tlemon at jlab.org>
Sent: Thursday, August 27, 2020 1:28 PM
To: Xiangdong Wei <xwei at jlab.org>; dsg-hdice at jlab.org <dsg-hdice at jlab.org>
Subject: Re: fsNMR front panel screenshot

Hi Xiangdong,

I was able to add the ability for the fsNMR program to take a screenshot at the end of all cycles. There will now be a file "end_run_screenshot.jpg" in each results directory with the screenshot.

I have logged off of HDiceNMR2 now.

Also, just for reference in case something happens to the hard drive on HDiceNMR2, whenever a change is made to the fsNMR program, I compress the program's directory and put a copy in O:\DSG_Slow_Controls\HDIce\DSG_NMR_fsNMR_Development\.

Tyler
________________________________
From: Xiangdong Wei <xwei at jlab.org>
Sent: Thursday, August 27, 2020 11:57 AM
To: Tyler Lemon <tlemon at jlab.org>
Subject: Re: fsNMR front panel screenshot

Tyler.

Great.

HDice was logout 5 minutes ago.

Thanks,

Xiangdong

________________________________
From: Tyler Lemon <tlemon at jlab.org>
Sent: Thursday, August 27, 2020 10:20 AM
To: Xiangdong Wei <xwei at jlab.org>; dsg-hdice at jlab.org <dsg-hdice at jlab.org>
Subject: Re: fsNMR front panel screenshot

Hi Xiangdong,

It should be no problem to finish by 4pm.

I don't expect it to take too long to add the screenshot feature.

Tyler
________________________________
From: Xiangdong Wei <xwei at jlab.org>
Sent: Thursday, August 27, 2020 9:48 AM
To: Tyler Lemon <tlemon at jlab.org>; dsg-hdice at jlab.org <dsg-hdice at jlab.org>
Subject: Re: fsNMR front panel screenshot

Hi Tyler,

Yes, you can logon at 12pm (I have a few short run to do and they will be done by noon).

Could I take it back by 4pm?

Thanks,

Xiangdong
________________________________
From: dsg-hdice <dsg-hdice-bounces at jlab.org> on behalf of Tyler Lemon <tlemon at jlab.org>
Sent: Thursday, August 27, 2020 8:00 AM
To: dsg-hdice at jlab.org <dsg-hdice at jlab.org>
Subject: [dsg-hdice] fsNMR front panel screenshot

Hi Xiangdong,

I was able to figure out how to get LabVIEW to take a screenshot of the front panel after all cycles have completed.

Would HDICENMR2 be available to remotely log into to add it to the fsNMR program?

Thanks,
Tyler
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hdice/attachments/20200827/ad0cd164/attachment-0001.html>