[FFA_CEBAF_Collab] FFA corrector concept

[Omar Garza]

Thanks,
Alex.
I had that information....just had a brain cell malfunction!!
Thanks again.
O'


Omar Garza
Deputy of Electrical Engineering Systems - Accelerator Reliability
Thomas Jefferson National Accelerator Facility
(757) 269-7257 garza at jlab.org<mailto:garza at jlab.org>
________________________________
From: Chase Dubbe <cdubbe at jlab.org>
Sent: Monday, August 22, 2022 11:15 AM
To: Omar Garza <garza at jlab.org>; Jay Benesch <benesch at jlab.org>; ffa_cebaf_collab at jlab.org <ffa_cebaf_collab at jlab.org>
Cc: Will Oren <oren at jlab.org>; Camille Ginsburg <ginsburg at jlab.org>; Mike Bevins <mbevins at jlab.org>; Joseph Meyers <meyers at jlab.org>; Alex Bogacz <bogacz at jlab.org>
Subject: Re: FFA corrector concept

Good Morning Omar,

To try to help, the FFA permanent magnets won't have a power requirement, but the Panofsky Quads that will be mounted along with them will. Based on the latest Magnet count sheet, there will be 50 of them per ARC (East/West) and reviewing Jay's technical write up, they should need 900W per magnet. He did mention that each would require two power supplies.

With regards to the counts though, there is some discrepancy. Jay, for each of the ARCs, is the number 50 or 100? Looking at your paper, vs the magnet count sheet, you are specifying 100 per ARC vs. the 50. Also, do my assumptions on power and power supply requirements line up with your specification?

[cid:e6d9ef9a-552c-471e-b389-b9c5801d6a03]
*Snap shot from Jay's paper 'FFA Corrector Concept'

        Name    L[cm]   B[kG]   G[kG/cm]        Number of magnets
        BD      50      3.1     4.7     200
        BF      50      5.5     1.5     200
Panofsky window quad, per Jay's sprec   100
*Cells Taken from 'New Magnet and RF Inventory' Excel

Thanks,
Chase
________________________________
From: Omar Garza <garza at jlab.org>
Sent: Monday, August 22, 2022 10:51 AM
To: Jay Benesch <benesch at jlab.org>; Chase Dubbe <cdubbe at jlab.org>; ffa_cebaf_collab at jlab.org <ffa_cebaf_collab at jlab.org>
Cc: Will Oren <oren at jlab.org>; Camille Ginsburg <ginsburg at jlab.org>; Mike Bevins <mbevins at jlab.org>; Joseph Meyers <meyers at jlab.org>; Alex Bogacz <bogacz at jlab.org>
Subject: Re: FFA corrector concept

Good morning everyone.
Does someone have the power requirements for the FFAs and new dipoles?
Thank you.
O'

Omar Garza
Deputy of Electrical Engineering Systems - Accelerator Reliability
Thomas Jefferson National Accelerator Facility
(757) 269-7257 garza at jlab.org<mailto:garza at jlab.org>
________________________________
From: Jay Benesch <benesch at jlab.org>
Sent: Monday, August 8, 2022 11:41 AM
To: Chase Dubbe <cdubbe at jlab.org>; ffa_cebaf_collab at jlab.org <ffa_cebaf_collab at jlab.org>
Cc: Will Oren <oren at jlab.org>; Omar Garza <garza at jlab.org>; Camille Ginsburg <ginsburg at jlab.org>; Mike Bevins <mbevins at jlab.org>; Joseph Meyers <meyers at jlab.org>; Alex Bogacz <bogacz at jlab.org>
Subject: Re: FFA corrector concept

Chase,

It is my understanding that each of the permanent magnets will require
one of these correctors.  Only two of the three windings per assembly
will likely be powered.  Hence the estimate of 400 units and 800 power
supplies.  It seems to me better to build all the units with the three
windings and power only two, to simplify fabrication and assembly.  And
we might need three in some locations. Rabbet joints assumed in the
steel to simplify assembly.

I'll send you the opc file for this under separate email.

Jay

On 8/8/22 11:27, Chase Dubbe wrote:
> Good Morning Jay,
>
> First, thank you for sharing all the other panofsky quad models. I have
> been out on vacation, so have not had a chance to look through them, but
> they are greatly appreciated.
>
> I am still trying to catch up, but for the cost estimate of these
> Picture Frame Correctors, is the intent to have one per each FODO set of
> permanent magnets in the FFA line, or will there be more or less? I just
> want to get a grasp at the quantity so that I can either use the cost
> estimate numbers Tommy Hiatt had developed, or perhaps go out for an RFI
> for cost.
>
> Thanks again for the help,
> Chase Dubbe'
> ------------------------------------------------------------------------
> *From:* Jay Benesch <benesch at jlab.org>
> *Sent:* Monday, August 8, 2022 10:18 AM
> *To:* ffa_cebaf_collab at jlab.org <ffa_cebaf_collab at jlab.org>
> *Cc:* Chase Dubbe <cdubbe at jlab.org>; Will Oren <oren at jlab.org>; Omar
> Garza <garza at jlab.org>; Camille Ginsburg <ginsburg at jlab.org>
> *Subject:* FFA corrector concept
> Attached please find a "picture frame" corrector concept which satisfies
> the requirements Stephen provided Friday. It should suffice for the cost
> estimate. Comments welcome.

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/ffa_cebaf_collab/attachments/20220822/402defed/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image.png
Type: image/png
Size: 49330 bytes
Desc: image.png
URL: <https://mailman.jlab.org/pipermail/ffa_cebaf_collab/attachments/20220822/402defed/attachment-0001.png>