[G14_run] [EXTERNAL] New g14 bi-weekly meeting time: Thursdays at 9:00 am Jlab time starting from tomorrow

[Tsuneo Kageya]

Hi Haiyun,

  thank you for the response.

  We expect that the flux ratios and Sigma and G asymmetries are the 
same or close between the two different vertex cuts.

  I am talking about the statistical errors for Sigma and G 
asymmetries.   I wonder -10 to -6 cm region has

the statistics by a factor of 4.0/2.7 = 1.48 larger than ones in the 
region -9.6 to -6.9 with a simple math.

        Regards, Tsuneo Kageya.


On 5/13/21 8:37 AM, Haiyun Lu wrote:
> I cannot join the meeting today. There is another meeting just today.
>
> Brief summary: I finished all the studies: systematics of fiducial 
> cut, compare with g13 results with and without penalty term, final 
> results without comparing to g13, corrected with the factor obtained 
> without penalty term, corrected with the factor obtained with penalty 
> term.
> I also varied the vertex selection from  between -9.6 and -6.9 to 
> between -10 and -6. The result has been compared. They are almost 
> identical. A linear fit indicates a factor 0.991 is needed for the 
> range between -10 and -6 to match with -9.6 and -6.9. I interpret it 
> as the effect of supporting materials inside the target.
>
> I am putting all these into the notes. I plan to finish it during the 
> weekends, unless I get some severe reaction from my second covid shot 
> tomorrow.
>
> On Wed, May 12, 2021 at 2:04 PM Tsuneo Kageya <kageya at jlab.org 
> <mailto:kageya at jlab.org>> wrote:
>
>     Ciao Annalisa,
>
>       thank you for arranging the meeting time.
>
>           Ciao, Tsuneo Kageya.
>
>
>     On 5/12/21 1:30 PM, Annalisa D'Angelo wrote:
>     > Dear All,
>     >
>     > the doodle has revealed that the best timing for everyone is on
>     every
>     > other Thursday at 9:00 am Jlab time.
>     >
>     > We can therefore simply anticipate our meeting by 30 minutes,
>     starting
>     > from tomorrow May 13th at 9:00 am.
>     >
>     > Direct meeting link is:
>     >
>     >
>     https://urldefense.proofpoint.com/v2/url?u=https-3A__bluejeans.com_593356414&d=DwICbA&c=CJqEzB1piLOyyvZjb8YUQw&r=xo4w5DaayvtvM8v3ApcUUA&m=m4cUTggr72JEwF_-QXP1AAOWuWy0W9f8CS57MoBK3fk&s=E1-rcs1gvUHcE78NsWd_EcfEBS-SKOK-0DyC3oK7hp8&e=
>
>     >
>     > Full meeting information is listed in the following.
>     >
>     > All the best
>     >
>     > Annalisa
>     >
>     > -------------------------------------------------
>     >
>     > The meeting info
>     >
>     > Meeting URL
>     >
>     https://urldefense.proofpoint.com/v2/url?u=https-3A__bluejeans.com_593356414-3Fsrc-3Djoin-5Finfo&d=DwICbA&c=CJqEzB1piLOyyvZjb8YUQw&r=xo4w5DaayvtvM8v3ApcUUA&m=m4cUTggr72JEwF_-QXP1AAOWuWy0W9f8CS57MoBK3fk&s=_K4hcPeD1SN87Tjxu8lPEJM6wEi2lsc2Oy8VDPPjYdI&e=
>
>     >
>     > Meeting ID
>     > 593 356 414
>     >
>     > Want to dial in from a phone?
>     >
>     > Dial one of the following numbers:
>     > +1.888.240.2560 (US Toll Free)
>     > (see all numbers -
>     >
>     https://urldefense.proofpoint.com/v2/url?u=https-3A__www.bluejeans.com_premium-2Dnumbers&d=DwICbA&c=CJqEzB1piLOyyvZjb8YUQw&r=xo4w5DaayvtvM8v3ApcUUA&m=m4cUTggr72JEwF_-QXP1AAOWuWy0W9f8CS57MoBK3fk&s=e1Ry3Hy2wtGBZQi62LAIZkL3xYqmKQ3ma81EEpcPDGk&e=
>
>     > )
>     >
>     > Enter the meeting ID and passcode followed by #
>     >
>     > Connecting from a room system?
>     > Dial: bjn.vc
>     <https://urldefense.proofpoint.com/v2/url?u=http-3A__bjn.vc&d=DwMFaQ&c=CJqEzB1piLOyyvZjb8YUQw&r=xo4w5DaayvtvM8v3ApcUUA&m=btHBOCunm0VhNZ3QefCxqkVGENGgKFrf3H7I-hyE3Q8&s=kRr6_1gFUkvj7JcN6KTN6UfxNohIVgN5EGV1Ber7G88&e=>
>     or 199.48.152.152 and enter your meeting ID & passcode
>     >
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/g14_run/attachments/20210513/1a657139/attachment-0001.html>