[Halld-controls] Hall D controls meeting on March 20 at 9:30am

[Hovane Egiyan]

Hi,

I posted the minutes of the last Hall D slow controls meeting and pasted
them to this message.

https://halldweb1.jlab.org/wiki/index.php/Controls_Meeting_20-Mar-2014#Minutes

Hovanes.


  Minutes


    [edit
    <https://halldweb1.jlab.org/wiki/index.php?title=Controls_Meeting_20-Mar-2014&action=edit&section=4>]UPS
    Requirements

  * Dave collected the information from Jonathan regarding the power for
    the valves
  * Yi would like to have the PXI system on the UPS as well (rated 300W)
  * Hovanes showed the layout of theUPS requirements in Hall D
    <https://halldweb1.jlab.org/wiki/images/1/1a/UPSforHallDreqs.pptx>(PXI
    was missing). Hovanes will send the requirements to Joe Beaufait on
    Friday.


    [edit
    <https://halldweb1.jlab.org/wiki/index.php?title=Controls_Meeting_20-Mar-2014&action=edit&section=5>]BCAL
    power supply interlocks

  * Dave showedslides
    <https://halldweb1.jlab.org/wiki/images/7/7f/Bcal_ps_interlocks.pptx>explaining
    his work on the BCAL interlocks.
  * Encountered strange problem that the 5V output modules on PoinIO did
    not provide enought current for the MPOD interlock input.
  * Dave will order CompactLogix extension modules to avoid PintIO all
    together, and use CompactLogix modules.
  * There was a request to change the button labels to adhere to Elton's
    convention.


    [edit
    <https://halldweb1.jlab.org/wiki/index.php?title=Controls_Meeting_20-Mar-2014&action=edit&section=6>]PLC
    archiving

  * Hovanes says that Paul Letta found that accumulated 12GB of data in
    the PLC_ARCHIVE_ON_CHANGE database. This database was active about
    one month. Therefore we need to reduce the rate at which this DB
    gets filled by PLC.
  * According to Dave, PLC only archived data for a short period of
    time, but it was not set up to be on-change.
  * Hovanes will remove the data from the PLC_ARCHIVE_ON_CHANGE table,
    and Dave will work on on-change archiving setup.


    [edit
    <https://halldweb1.jlab.org/wiki/index.php?title=Controls_Meeting_20-Mar-2014&action=edit&section=7>]Radiator
    stage test

  * Hovanes said that the radiator insertion stage has been installed on
    the laser table in room 213 in FEL by Yi, Slava and himself, the
    same palce where the goniometer was tested. Scot and Tina made the
    cables to connect the stage to the XPS controller. Using a laser
    system the stage will be tested.


    [edit
    <https://halldweb1.jlab.org/wiki/index.php?title=Controls_Meeting_20-Mar-2014&action=edit&section=8>]Suggested
    modification to voltage controls

  * Elton said that he will e-mail a list of suggestion for improvements
    the BCAL voltage controls software (see Elton's future e-mail below).

Hi Nerses,

I have been compiling feedback on the BCAL HV control

1. Would like to highlight the channel that has been selected. At the
moment the channel number is displayed, but it would be nice to have a
visual clue to point to the selected channel
2. The "show bias channels" window will not allow the voltage to be set
above 70 V. The "set bias channels" window does not have this restriction.
3. The histogram display of the current is not operational
4. In the "set bias channels" window the measured temperature seems to
display the measured voltage.
5. The "red" status on the overall display will remain ON even if some
of the HV channels are on. The status will only turn green if all four
HV channels from a given module are all on. For example, if one of the
four HV channels from one module is off, that module will show "red".
However, it is good to be able to look at the overall display and see if
ANY channels are on. We may need to add another color, e.g. orange, that
would show that some of the HV channels are on.

* Finally, the issue of some channels staying at zero volts, even if the
set voltage is 75 V. Yesterday I found this problem for BCAL module 13,
which is a completely different HV module from previously identified
module. I will continue to debug this; in the previous case, the
channels were cleared when we unplugged the IPOD crate and rebooted the IOC.

Thanks, Elton.


  [edit
  <https://halldweb1.jlab.org/wiki/index.php?title=Controls_Meeting_20-Mar-2014&action=edit&section=9>]Action
  Items

  * Dave will order CompactLogix extensions with 5V output modules for
    BCAL interlocks.
  * Dave will modify the buttons on the BCAL interlocks to match Elton's
    convention.
  * Hovanes will send the UPS requirements to Joe Beaufait (after
    including Yi's PXI system requirements).
  * Hovanes will remove all the data from PLC_ARCHIVE_ON_CHANGE.
  * Elton will send an e-mail with his suggestions for BCAL voltage
    controls improvements.


-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://mailman.jlab.org/pipermail/halld-controls/attachments/20140327/dbbb961c/attachment.html