[Dsg-rich] RICH compressors successfully powered

[Ronald Bartek]

Walt 

Am I correct in assuming these are the two (2) Atlas Copco compressors and the one in Bldg. 90 is connected to the ASME Pressure vessel shown in the attachment? Also I was told that the pressure vessel will be relocated in the future to Hall B along with the corresponding air compressor. Correct? 







From: "Walt Akers" <akers at jlab.org> 
To: "Carroll Jones" <jonesc at jlab.org> 
Cc: "Tyler Lemon" <tlemon at jlab.org>, "dsg-rich" <dsg-rich at jlab.org>, "Michael Sprouse" <msprouse at jlab.org>, "Ronald Bartek" <bartek at jlab.org> 
Sent: Monday, July 31, 2017 11:42:05 AM 
Subject: Re: [Dsg-rich] RICH compressors successfully powered 

These are air compressors... 

Carroll Jones wrote: 
> Is this compressor an air compressor or refrigeration compressor? Drainage from her compresses have all and must be removed before draining into the sanitary drain. 
> 
> For additional information or clarification, please contact me at 757–8 76–1778. 
> 
> Sincerely, 
> 
> Carroll W Jones 
> 
> Sent from my iPhone 
> 
>> On Jul 31, 2017, at 9:17 AM, Walt Akers <akers at jlab.org> wrote: 
>> 
>> Tyler: 
>> 
>> There are a variety of drains nearby. The most likely candidate would 
>> be in one of the utility closets on the main hallway. Notably, this would 
>> probably require the installation of a small pump to deliver the water 
>> from the compressor to the utility room. 
>> 
>> I'm CCing Carroll Jones on this, because it would certainly involve 
>> some design support from Facilities to make this happen (unless there 
>> is already a floor drain nearby). 
>> 
>> Walt 
>> 
>> Tyler Lemon wrote: 
>>> Hello, 
>>> 
>>> One note left out from my email on Friday: we found during the test of the EEL compressor that there is a drain on each of the compressors where water will shoot out every few minutes. 
>>> 
>>> The drain needs a 5/16-inch diameter line to lead to some sort of reservoir. Brian and I tried to find a 5/16-inch diameter line in the Hall B Gas Shed but could not find one. Do we have anything that could be used for the compressor drain line? 
>>> 
>>> To hold the drain water, a temporary solution could be to use a bucket, but we do not know how much water is produced in a given time so there is a chance the bucket could overflow if not checked regularly. 
>>> 
>>> Walt, 
>>> Is there already a drain in EEL 125 that we could run the compressor's drain line to? 
>>> 
>>> Doug, 
>>> Is there someplace the compressors could drain to in Hall B? 
>>> 
>>> Best regards, 
>>> Tyler 
>>> 
>>> ------------------------------------------------------------------------ 
>>> *From: *"Tyler Lemon" <tlemon at jlab.org> 
>>> *To: *"dsg-rich" <dsg-rich at jlab.org>, "DeAnn Maddox" <maddox at jlab.org>, "Walt Akers" <akers at jlab.org>, "Joshua Johnson" <joshua.johnson at us.atlascopco.com>, "paul stanko" <paul.stanko at us.atlascopco.com> 
>>> *Sent: *Friday, July 28, 2017 4:56:41 PM 
>>> *Subject: *[Dsg-rich] RICH compressors successfully powered 
>>> 
>>> Hello, 
>>> 
>>> This afternoon we successfully powered on both RICH compressors in the EEL and Hall B. 
>>> 
>>> For the compressor in the EEL, we turned it on and set a maximum output pressure of 70 psi on the compressor. We then let the compressor run until it turned itself off when reaching an output pressure of 70 psi. After this, we stopped the compressor and vented the attached gas tank. We also got the MAC address for this compressor and Brian has contacted Sergey to get an IP address assigned to the compressor. The compressor's emergency stop button has been pressed, preventing the compressor output from being enabled. 
>>> 
>>> For the compressor in Hall B, we only turned it on and made sure that it is able to run correctly. We left this compressor powered on, but not running. 
>>> 
>>> Thank you to DeAnn for making sure all visitors were properly registered to be able to get on site. Thank you to Walt for quickly arranging the short-notice electrical work that needed to be done today. Also, thank you to Paul and Joshua, the Atlas Copco representatives, for helping us get the compressors running. 
>>> 
>>> Best regards, 
>>> Tyler 
>>> 
>>> _______________________________________________ 
>>> Dsg-rich mailing list 
>>> Dsg-rich at jlab.org 
>>> https://mailman.jlab.org/mailman/listinfo/dsg-rich 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hallb_rich/attachments/20170731/ce17948c/attachment-0002.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Thunderbird signature.jpg
Type: image/jpeg
Size: 31486 bytes
Desc: not available
URL: <https://mailman.jlab.org/pipermail/dsg-hallb_rich/attachments/20170731/ce17948c/attachment-0004.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: NB795119.jpg
Type: image/jpeg
Size: 231176 bytes
Desc: not available
URL: <https://mailman.jlab.org/pipermail/dsg-hallb_rich/attachments/20170731/ce17948c/attachment-0005.jpg>