[Dsg-rich] Schedule RICH stiffening tool load test
Marco Mirazita
Marco.Mirazita at lnf.infn.it
Mon Oct 9 10:01:22 EDT 2017
Hi Tyler,
for me tomorrow at 9 am is ok.
Marco
Il 2017-10-09 15:21 Tyler Lemon ha scritto:
> Hello Mark, Dario, and Sandro,
>
> I can set up a Bluejeans meeting for 9:00AM on October 10, 2017.
>
> Those of us at JLab could meet in the DSG control room (EEL 121c) at
> 9:00AM JLab time to start the meeting on Bluejeans with Sandro.
>
> We would then be able to move to EEL 125 to look at the stiffening
> tool and load test components if there are any more questions.
>
> Please let us know if 9:00AM is a good time for the meeting.
>
> Best regards,
>
> Tyler
>
> -------------------------
>
> FROM: "dario orecchini" <dario.orecchini at lnf.infn.it>
> TO: "Mark Loewus" <loewus at jlab.org>, "Tomassini Sandro"
> <sandro.tomassini at lnf.infn.it>, "Tyler Lemon" <tlemon at jlab.org>
> CC: "dsg-rich" <dsg-rich at jlab.org>, "Bob Miller" <rmiller at jlab.org>
> SENT: Sunday, October 8, 2017 2:21:03 PM
> SUBJECT: RE: [Dsg-rich] Schedule RICH stiffening tool load test
>
> Mark, Tyler & Sandro
>
> I propose to have a meeting (Bluejeans or Skype) on Tuesday, 9:00 am
> JLab time / 15:00 Italy time.
>
> In such a way we could have a discussion with Sandro too.
>
> Let me know, Dario
>
> Sent from Mail [1] for Windows 10
>
> FROM: Mark Loewus
> SENT: Friday, October 6, 2017 9:49 PM
> TO: Tomassini Sandro; Tyler Lemon
> CC: dsg-rich at jlab.org; Bob Miller
> SUBJECT: Re: [Dsg-rich] Schedule RICH stiffening tool load test
>
> Sandro, Tyler,
>
> I am glad to help with the load test. I am fairly new to the lab and
> this is going to be my first load test at the lab. I will need
> everyone's support to perform this load test successfully. I don't
> have any employees that directly work for me.
>
> I think we should schedule the load test after we make sure we have
> all the appropriate equipment, rigging and test weights. I will write
> the lift plan once I understand how the weights will be attached to
> the stiffening tool. We will need to gather the appropriate amount of
> test weights and borrow Doug Tilles dynamometer for the test.
>
> I need to understand where and how the test load should be attached to
> the fixture so the load is applied correctly without damaging the tool
> during the test. I also need to understand the orientation of the
> fixture during load test or tests.
>
> Since Bob Miller is extremely busy in hall "B", I don't think it is a
> good time to do a test in hall "B".
>
> We should meet to discuss how and where we are going to proceed with
> the load test. I will be busy on Monday dealing with a crane repair at
> the CHL. Tuesday would be a better day to meet and discuss.
>
> Respectfully,
>
> Mark Loewus
>
> Manager of Crane Services
>
> Phone- 757-269-7847
>
> Cell- 757-871-3072
>
> Email- Loewus at jlab.org
>
> ----- Original Message -----
>
> From: "Tomassini Sandro" <sandro.tomassini at lnf.infn.it>
>
> To: "Tyler Lemon" <tlemon at jlab.org>
>
> Cc: "Mark Loewus" <loewus at jlab.org>, dsg-rich at jlab.org, "Bob Miller"
> <rmiller at jlab.org>, "Doug Tilles" <tilles at jlab.org>
>
> Sent: Friday, October 6, 2017 1:42:41 PM
>
> Subject: Re: [Dsg-rich] Schedule RICH stiffening tool load test
>
> Hello I answer to Mark,
>
> About the load weight suspention a specific drawing does not exist
> since it was agreed with Miller to procede in this way:
>
> -Use a metal basket with lead bricks, you can find them in the hall b
> or ask to Bob or Doug
>
> - attach the basket to the test stand using two straps.
>
> - Dario Orecchini can help you.
>
> For any question do not hesitate to ask.
>
> Many thanks
>
> Sandro
>
> Inviato da Blue
>
> Il giorno 6 ott 2017 19:19, alle ore 19:19, Tyler Lemon
> <tlemon at jlab.org> ha scritto:
>
>> Hello Mark,
>
>>
>
>> Attached is a document from INFN collaborators containing details of
>
>> the stiffening tool part and load test we need to perform. These
>
>> details can be found on page 22.
>
>>
>
>> As you would be the person performing the load test, would you also
>
>> write the lift plan? Also do you have any recommendations on a place
>
>> this load test could occur?
>
>>
>
>> If you would need to meet to discuss the part and load test, I would
> be
>
>> available to meet you this afternoon or on Monday.
>
>>
>
>> Please let us know.
>
>>
>
>> Also, if you could "Reply All" to to this email when you reply to
>
>> ensure it goes to the dsg-rich at jlab.org mailing list, all
> collaborators
>
>> would be able to answer any questions you have.
>
>>
>
>> Best regards,
>
>> Tyler
>
>>
>
>>
>
>> From: "Mark Loewus" <loewus at jlab.org>
>
>> To: "Tyler Lemon" <tlemon at jlab.org>
>
>> Sent: Thursday, October 5, 2017 2:41:10 PM
>
>> Subject: Re: Schedule RICH stiffening tool load test
>
>>
>
>> Tyler,
>
>>
>
>> You will have to coordinate an effort to find an adequate place to
> load
>
>> test. Do you have a drawing of how the test weights will be suspended
>
>> from the fixture. A lift plan needs to be developed and I need to
>
>> review it before the load test is conducted. Give me a call if you
>
>> needed.
>
>>
>
>> Mark Loewus
>
>> Manager of Crane Services
>
>> Phone- 757-269-7847
>
>> Cell- 757-871-3072
>
>> Email- Loewus at jlab.org
>
>>
>
>> ----- Original Message -----
>
>> From: "Tyler Lemon" <tlemon at jlab.org>
>
>> To: "Mark Loewus" <loewus at jlab.org>
>
>> Cc: "dsg-rich" <dsg-rich at jlab.org>
>
>> Sent: Thursday, October 5, 2017 11:00:29 AM
>
>> Subject: Re: Schedule RICH stiffening tool load test
>
>>
>
>> Hello Mark,
>
>>
>
>> The plan to load test RICH's stiffening tool is to use the trolley
>
>> formerly for transportation of Hall B's drift chambers to attach a
> test
>
>> load to RICH's stiffening tool. In the attached PDF, page 1 shows a
>
>> diagram of the stiffening tool on the trolley with a test load.
>
>>
>
>> I do not know where this load test can be performed or what item will
>
>> be used as the test weight as up until October 3, Hall B Engineering
>
>> was to perform the load test.
>
>>
>
>> Will we need to take the trolley and stiffening tool to a specific
>
>> location for the load test?
>
>>
>
>> Best regards,
>
>> Tyler
>
>>
>
>>
>
>>
>
>>
>
>> From: "Mark Loewus" <loewus at jlab.org>
>
>> To: "Tyler Lemon" <tlemon at jlab.org>
>
>> Sent: Wednesday, October 4, 2017 10:13:26 AM
>
>> Subject: Re: Schedule RICH stiffening tool load test
>
>>
>
>> Tyler,
>
>>
>
>> I need to understand how you will conduct the load test. Please, give
>
>> me a call so we can discuss. What is the SWL of the lifting device.
>
>>
>
>> Mark Loewus
>
>> Manager of Crane Services
>
>> Phone- 757-269-7847
>
>> Cell- 757-871-3072
>
>> Email- Loewus at jlab.org
>
>>
>
>> ----- Original Message -----
>
>> From: "Tyler Lemon" <tlemon at jlab.org>
>
>> To: "Mark Loewus" <loewus at jlab.org>, "dsg-rich" <dsg-rich at jlab.org>
>
>> Sent: Tuesday, October 3, 2017 9:32:13 AM
>
>> Subject: Schedule RICH stiffening tool load test
>
>>
>
>> Hello Mark,
>
>>
>
>> We need to schedule a load test for the RICH stiffening tool that
> will
>
>> be used to lift Hall B's RICH onto its transportation trolley.
>
>>
>
>> Bob Miller has stated we should contact you for the load test.
>
>>
>
>> Could we schedule the stiffening tool's load test for the morning of
>
>> October 11, 2017?
>
>>
>
>> Please let us know.
>
>>
>
>> Best regards,
>
>> Tyler
>
>>
>
>>
>
>> From: "Bob Miller" <rmiller at jlab.org>
>
>> To: "Tyler Lemon" <tlemon at jlab.org>
>
>> Cc: "Doug Tilles" <tilles at jlab.org>
>
>> Sent: Monday, October 2, 2017 1:11:42 PM
>
>> Subject: Re: Schedule RICH stiffening tool load test
>
>>
>
>>
>
>>
>
>> Please see Doug Tilles's email from last month. The load test should
> be
>
>> done by Mark Loewus from Facilities.
>
>>
>
>> Regards,
>
>>
>
>> Bob
>
>>
>
>>
>
>>
>
>> On 9/29/2017 9:54 AM, Tyler Lemon wrote:
>
>>
>
>>
>
>>
>
>> Hello Bob,
>
>>
>
>> We should receive the required parts to be able to load test the RICH
>
>> stiffening tool from G&R Metals by Friday October 6, 2017.
>
>>
>
>> Could we schedule the stiffening tool's load test for October 10,
> 2017?
>
>>
>
>>
>
>> Please let us know when the load test can be scheduled.
>
>>
>
>> Best regards,
>
>> Tyler
>
>>
>
>>
>
>>
>
>> --
>
>> Bob Miller
>
>> Hall B Lead Engineer
>
>> Jefferson Lab
>
>> 757 269-7867
>
>>
>
>>
>
>> ------------------------------------------------------------------------
>
>>
>
>> _______________________________________________
>
>> Dsg-rich mailing list
>
>> Dsg-rich at jlab.org
>
>> https://mailman.jlab.org/mailman/listinfo/dsg-rich
>
> _______________________________________________
>
> Dsg-rich mailing list
>
> Dsg-rich at jlab.org
>
> https://mailman.jlab.org/mailman/listinfo/dsg-rich
>
>
>
> Links:
> ------
> [1]
> https://urldefense.proofpoint.com/v2/url?u=https-3A__go.microsoft.com_fwlink_-3FLinkId-3D550986&d=DwMFaQ&c=lz9TcOasaINaaC3U7FbMev2lsutwpI4--09aP8Lu18s&r=f-t6QoIPtnKcbZffsXp7zA&m=qFug-RHVOUCfORTzeW68loA4nI9YwofHWtckb5zI50s&s=n0A4vgXXhMOxOxfrvn1A5yuWVrIAk-21ihPuSFMdto4&e=
>
> _______________________________________________
> Dsg-rich mailing list
> Dsg-rich at jlab.org
> https://mailman.jlab.org/mailman/listinfo/dsg-rich
More information about the Dsg-rich
mailing list