[Dsg-hallc_controls] [EXTERNAL] Re: CAEN JLAB - EPICS control - 2 part
Greg Kibilko
greg at setechsales.com
Wed Jan 29 07:14:23 EST 2020
Hi Aaron,
One quick question. When this HV mainframe system was purchased Brad
also ordered an A4532 booster power supply. Is that booster installed
in the mainframe you are testing?
Thanks,
Greg
On 1/28/2020 1:52 PM, Aaron Brown wrote:
> Hello Alberto,
>
> Another quick thought:
>
> After speaking to Pablo, I thought it may be helpful to mention that
> the issue with random parameter changes while using EPICS has not been
> observed when only one board is populated in the crate. Previously
> when we have seen these parameter changes we have been operating with
> a fully populated crate, so this may be one reason you have not been
> able to reproduce this issue.
>
> Just a thought.
>
> Warm regards,
> Aaron Brown
> ------------------------------------------------------------------------
> *From:* Alberto Lucchesi <a.lucchesi at caen.it>
> *Sent:* Tuesday, January 28, 2020 12:28 PM
> *To:* Aaron Brown <ambrown at jlab.org>; dsg-hallc controls
> <dsg-hallc_controls at jlab.org>
> *Cc:* Greg Kibilko <greg at setechsales.com>; Gianni Di Maio
> <g.dimaio at caen.it>; Nicola Paoli <n.paoli at caen.it>
> *Subject:* [EXTERNAL] Re: CAEN JLAB - EPICS control - 2 part
> Hi Aaron,
>
> after my answer to your email I had a brainstorming with my colleagues
> of HV division concerning the issue 2.
> We don't have yet an explanation of that wrong behavior and there some
> question we would like ask you.
>
> 1) thet load is 2 MΩ for each channel, but which is the voltage of
> each channel?
> 2) the board that, let'say, "disappear" could be one with the load
> attached or one without load, we need to knwo how many boards are
> inserted in the Sy4527 and how many of them have the load.
>
> 3) Can you verify if each of the boards (with the load) on the setup
> that shows the issue have the pins in the right position? One of our
> hypotesis is that if the pins ( male and female) are not well plugged,
> it is possible that a bad contact could induce discharges that power
> off that board or one next to that..
>
> Best Regards,
> Alberto
>
>
>
--
*Greg Kibilko*
*SETS - SE Technical Sales, Inc.*
112 Tyra Lane
Townville, SC 29689
P: (864) 356-2606
CAEN Products <https://urldefense.proofpoint.com/v2/url?u=http-3A__www.caen.it_csite&d=DwIDaQ&c=CJqEzB1piLOyyvZjb8YUQw&r=0dv9yTu0KREdd74L0wgLztdO3ePmhsIUc7EqYumdPxc&m=VoJV5AxzKEd3dA_wQuZANW3bw7ah6CBtP0DdhHx8U_A&s=v_Oki6nUOrzSsHIMMwqDBOJiFr3q_8AX6vy_u7G-3qA&e= >
CAEN SyS Products & Solutions <https://urldefense.proofpoint.com/v2/url?u=https-3A__caensys.com_products-2Dand-2Dsolutions_&d=DwIDaQ&c=CJqEzB1piLOyyvZjb8YUQw&r=0dv9yTu0KREdd74L0wgLztdO3ePmhsIUc7EqYumdPxc&m=VoJV5AxzKEd3dA_wQuZANW3bw7ah6CBtP0DdhHx8U_A&s=l_HwpKyqterhOrQUTE_x5U0WmMLYIcQpMuykqv4X_O0&e= >
IOxOs Products <https://urldefense.proofpoint.com/v2/url?u=http-3A__www.ioxos.ch&d=DwIDaQ&c=CJqEzB1piLOyyvZjb8YUQw&r=0dv9yTu0KREdd74L0wgLztdO3ePmhsIUc7EqYumdPxc&m=VoJV5AxzKEd3dA_wQuZANW3bw7ah6CBtP0DdhHx8U_A&s=jQdeOEquTReViXzSJ7oIeX1UA65f7fk-p0kefGWcyZU&e= >
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hallc_controls/attachments/20200129/47f291fa/attachment.html>
More information about the Dsg-hallc_controls
mailing list