[Dsg-hallc_nps] [EXTERNAL] Re: Re: LED cables for NPS setup ? where are they ?

[Simona Malace]

Hello All,

I attach a picture of a short led cable as it would be cabled on the detector and a picture of same cable against the LED driver.

Is there a transitional connection to account for the difference in connector size?

Best Regards

Simona

Get Outlook for Android<https://aka.ms/AAb9ysg>
________________________________
From: Dsg-hallc_nps <dsg-hallc_nps-bounces at jlab.org> on behalf of Brad Sawatzky via Dsg-hallc_nps <dsg-hallc_nps at jlab.org>
Sent: Wednesday, February 8, 2023 5:13:59 PM
To: Aaron Brown <ambrown at jlab.org>; Robert Michaels <rom at jlab.org>; Aaron Brown via Dsg-hallc_nps <dsg-hallc_nps at jlab.org>; Brad Sawatzky <brads at jlab.org>; yeran at jlab.org <yeran at jlab.org>; Bryan Moffit <moffit at jlab.org>; Chris Stanislav <stanisla at jlab.org>; Carlos Munoz Camacho <munoz at jlab.org>
Cc: Patrizia Rossi <rossi at jlab.org>
Subject: [Dsg-hallc_nps] [EXTERNAL] Re: Re: LED cables for NPS setup ? where are they ?

Those are/were the cables.   The parts  (cables and connectors) were in EEL/108.


On February 8, 2023 10:11:32 PM GMT+02:00, Aaron Brown <ambrown at jlab.org> wrote:
Hi Brad, Bob et al.,

After looking at all emails I could find I don't see that the fabrication of LED cables was discussed anywhere.
The only thing I see is a line item on the NPS Tasklist (line 83) to procure 60 new ribbon cables tasked to the FEG, DSG, and Brad.
Are these the cables for the LEDs?
Are the materials for these cables on-hand?
Perhaps the FEG should make these cables, since they made the boards to which they connect?

-- Aaron
________________________________
From: Dsg-hallc_nps <dsg-hallc_nps-bounces at jlab.org> on behalf of Brad Sawatzky via Dsg-hallc_nps <dsg-hallc_nps at jlab.org>
Sent: Wednesday, February 8, 2023 12:49 PM
To: Robert Michaels <rom at jlab.org>; Aaron Brown via Dsg-hallc_nps <dsg-hallc_nps at jlab.org>; Brad Sawatzky <brads at jlab.org>; yeran at jlab.org <yeran at jlab.org>; Bryan Moffit <moffit at jlab.org>; Chris Stanislav <stanisla at jlab.org>; Carlos Munoz Camacho <munoz at jlab.org>
Subject: [Dsg-hallc_nps] [EXTERNAL] Re: LED cables for NPS setup ? where are they ?

They may still need to be fabricated.  The parts were all in EEL 108.  The DSG had it on their list at one point along with the controls work.


On February 8, 2023 7:42:36 PM GMT+02:00, Robert Michaels <rom at jlab.org> wrote:
Dear all

Casting a wide net with this question.  Simona is organizing the finishing of the cabling of the NPS detector in the EEL108  setup, and it's going well.   But we don't know where the LED cables are.  Does anyone know where are the LED cables that run from detector to the led driver?  She will need those so that the hall C techs can install them.

thank you!

Sincerely,

Bob Michaels
--
Sent from my Android phone with K-9 Mail. Please excuse my brevity.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hallc_nps/attachments/20230208/68522a25/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: IMG_20230208_173735427_HDR.jpg
Type: image/jpeg
Size: 3174407 bytes
Desc: IMG_20230208_173735427_HDR.jpg
URL: <https://mailman.jlab.org/pipermail/dsg-hallc_nps/attachments/20230208/68522a25/attachment-0002.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: IMG_20230208_173754717_HDR.jpg
Type: image/jpeg
Size: 2670728 bytes
Desc: IMG_20230208_173754717_HDR.jpg
URL: <https://mailman.jlab.org/pipermail/dsg-hallc_nps/attachments/20230208/68522a25/attachment-0003.jpg>