[Dsg-rich] Update to the Trolley Parts

[Marc McMullen]

Hi Dario,

I am not sure if you intended to send the attachment. There was not an 
attachment on your last email. If you already sent them to Bob, he can 
just send it to me when it is approved.

Regards,

Marc


On 9/8/2017 11:04 AM, dario.orecchini at lnf.infn.it wrote:
>
> Hi Marc,
>
> Attached the complete updated series of drawings regarding the 
> additional structure for the trolley.
>
> In detail:
>
> _____________________________________________________________________
>
> 2_8 Forward RICH-Trolley Anchoring System_Assembly_REV 1_05-09-2017
>
> 3_8 Forward RICH-Trolley Anchoring System_Part_REV 1_05-09-2017
>
> 4_8 Forward RICH-Trolley Anchoring System_Part_REV 1_05-09-2017
>
> _____________________________________________________________________
>
> 5_8 Backward RICH-Trolley Anchoring System_Assembly_REV 1_05-09-2017
>
> 6_8 Backward RICH-Trolley Anchoring System_Part_REV 1_05-09-2017
>
> 7_8 Backward RICH-Trolley Anchoring System_Part_REV 1_05-09-2017
>
> _____________________________________________________________________
>
> I added a PPoint file were is highlighted an example of the “Revision 
> and Date Update” on my drawings.
>
> In the previous transmission of drawings:
>
>   * I did’t send the drawings 4_8 and 7_8 because any modification
>     have been done.
>   * A date of the update has been added on the title block of the drawings
>   * A date of the update has been added at the title of the files.
>
> Anyway, sorry and I hope that this time is the right time.
>
> Regards
>
> Dario
>
> Sent from Mail 
> <https://urldefense.proofpoint.com/v2/url?u=https-3A__go.microsoft.com_fwlink_-3FLinkId-3D550986&d=DwMFaQ&c=lz9TcOasaINaaC3U7FbMev2lsutwpI4--09aP8Lu18s&r=QXCvu8QK6ikaH4obIVOnE99umgkKvVo3REsRfybrlqs&m=CEyuwEWu5gwN9p6ekR2NSUpM2T1-Aq1XphD-7ILtXkM&s=J5lk9EQGyV1HrXSwsGm6YG4zYNWW_7W6w6cWWuOZMns&e=> 
> for Windows 10
>
> *From: *Marc McMullen <mailto:mcmullen at jlab.org>
> *Sent: *Friday, September 8, 2017 3:25 PM
> *To: *'dsg-rich' <mailto:dsg-rich at jlab.org>; Bob Miller 
> <mailto:rmiller at jlab.org>
> *Subject: *Re: [Dsg-rich] Update to the Trolley Parts
>
> Hi Dario,
>
> We have looked into the issue with the drawings for the Trolley parts. 
> It looks like the drawings have been corrected however Jlab has sent 
> the shop drawings on multiple occasions.
>
> 1. Quote
>
> 2. Procurement Quote
>
> 3. Final
>
> 4. Revised Trolley parts (partial set)
>
> The Trolley part set should be combined with the revised Trolley parts 
> and reissued as a set. When the set is done all pages should have the 
> revision section of the title block updated. For instance (Rev. 5), 
> once done Bob can check the drawings and let me know and I will ask 
> GandR to throw out all the old drawings and only used the new revision 
> set.
>
> Regards,
>
> Marc
>
> On 9/7/2017 2:23 PM, Marc McMullen wrote:
>
>     Hi Dario,
>
>     GandR just called and requested that you review the Trolley parts
>     drawings. Sheet 3_8 and 6_8 of the updated drawings have hole
>     spacings on the I-beam of 2.3 inches but the lateral and central
>     counterplates on 4_8 and 7_8 were not adjusted. So the drawing has
>     them at 2.5 inches.
>
>     Please review the drawings and communicate changes with Bob Miller.
>
>     Bob,
>
>     After you approve of the changes please let me know and I will
>     forward the info to the shop and tell them to proceed. Currently,
>     they are holding on the Trolley parts.
>
>     Regards,
>
>
>
>
>     _______________________________________________
>
>     Dsg-rich mailing list
>
>     Dsg-rich at jlab.org <mailto:Dsg-rich at jlab.org>
>
>     https://mailman.jlab.org/mailman/listinfo/dsg-rich
>
>
>
> -- 
> Marc McMullen
> Detector Support Group
> 757-269-7738
>

-- 
Marc McMullen
Detector Support Group
757-269-7738

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hallb_rich/attachments/20170908/7027001a/attachment-0002.html>