[Eg6_analysis] Calibration cooking

[hattawy at ipno.in2p3.fr]

Hello Lamiaa,
   Thank you very much. This is perfect to process two files.

Best regards,
Mohammad Hattawy.



> Hi Mohammad,
>
> Upon your request, I have processed the full list of 1.2 GeV 4He runs (117
> runs).
> The HROOT outputs are saved in the following directory:
> /volatile/clas/claseg6/gempass1_v1/1p2gev/HROOT/.
>
> As for your request to process 400K events for the other beam energies, I
> processed
> the first two bosfiles (*.A00 & *.A01) for 5.7 GeV runs since the 1st
> boshas less than
> the events requested. These HROOT files are saved in this directory:
> /volatile/clas/claseg6/gempass1_v1/5p7gev/HROOT/.
>
> I am currently processing the same two files of 6 GeV runs even if the 1st
> bos has more
> than 400K events. In case there is an issue with the 1st bos you may use
> the second one.
> I will let you know when the cooking of 6 GeV dataset is done.
>
> Regards,
>
> Lamiaa
>
>
>
>
> On Thu, Jul 11, 2013 at 2:37 PM, Mohammad Hattawy <
> mohammad.hattawy at gmail.com> wrote:
>
>> Hello all,
>>    So, we all agree that HROOT output files will be enough, and we do
>> not
>> need BOS files.
>> Lamiaa, you can go with the cooking if this is fine.
>>
>> Regards,
>> Mohammad.
>>
>>
>> On Thu, Jul 11, 2013 at 3:09 PM, Nathan Baltzell <baltzell at anl.gov>
>> wrote:
>>
>>> **
>>> Hello Mohammad,
>>>
>>> HROOT with TPCC will have all raw info about all hits in all
>>> reconstructed
>>> tracks.  Lamiaa's tcl that was attached does have the "ltpcc_nt_do"
>>> flag,
>>> which will turn on the TPCC variables in the ntuple.
>>>
>>> -nathan
>>>
>>>
>>>
>>> On Thu, 11 Jul 2013 02:58:48 -0500, Mohammad Hattawy <
>>> mohammad.hattawy at gmail.com> wrote:
>>>
>>> Hello Lamiaa,
>>>
>>>    For the run lists, we need all the 1.2 GeV runs with 4He target, and
>>> the first file of each run of 5.7 GeV and 6 GeV. If it is easier for
>>> you to
>>> pick a fixed number of statistics from each run, I would say we need
>>> the
>>> first 400 000 events from all the 6  and 5.7 GeV.
>>>   Regarding the output files, I would say that HROOT is enough. Nathan,
>>> do we need BOS files also?
>>>   For the tcl file, i think it is fine.
>>>
>>> Best regards,
>>> Mohammad.
>>>
>>>
>>> On Wed, Jul 10, 2013 at 3:52 PM, Lamiaa El Fassi
>>> <lamiomar at gmail.com>wrote:
>>>
>>>> Hi Raphael,
>>>>
>>>> In case the information that you need is included in the TPCC bank, as
>>>> Nathan mentioned,
>>>> I may need to process few runs for you since the TPCC, which is a
>>>> calibration bank, was not
>>>> turned on in the pass1v1 production pass. For this task I am
>>>> suggesting
>>>> the following:
>>>>
>>>> 1. Could you check different beam energy run lists posted in the
>>>> cooking
>>>> link
>>>> (here<https://clasweb.jlab.org/rungroups/lowq/wiki/index.php/Cooking_Notes>)
>>>> and pick
>>>> the runs that you want me to process? Please specify also how much
>>>> statistics you may need
>>>> for each run!
>>>> 2. Could you specify also the type of output files that you need; BOS
>>>> or
>>>> HROOT files or both?
>>>> In this case I will save the output files only on Volatile disk not on
>>>> Silo.
>>>> 3. Could you check the attached tcl file which I am usually using for
>>>> the RTPC calibration to see
>>>> if all what you need for this RTPC calibration check is included?
>>>>
>>>> Best regards,
>>>>
>>>> Lamiaa
>>>>
>>>>
>>>> On Tue, Jul 9, 2013 at 5:02 PM, Nathan Baltzell
>>>> <baltzell at anl.gov>wrote:
>>>>
>>>>> Hi Rapha�l,
>>>>>
>>>>> Yes, I think the TPCC bank should be sufficient.  It has TDCs, raw
>>>>> ADCs,
>>>>> and also gain-calibrated ADCs for every hit used in the GCPB bank,
>>>>> which
>>>>> has some very loose cuts to remove junk tracks.  Each TPCC hit has a
>>>>> pointer to the GCPB track it was associated with.  That raw
>>>>> information
>>>>> cannot be gotten from only cooked pass1v1 data.
>>>>>
>>>>> Regards,
>>>>> Nathan
>>>>>
>>>>>
>>>>>
>>>>> On Tue, 09 Jul 2013 09:57:52 -0500, Dupr� Rapha�l <
>>>>> raphael.dupre at gmail.com> wrote:
>>>>>
>>>>>  Dear Lamiaa and Nathan,
>>>>>>
>>>>>> We are starting to work again on the RTPC calibration. One of the
>>>>>> points that we would like to check is that the calibration is not
>>>>>> changing during the run.
>>>>>>
>>>>>> We would need the detailed tpc bank which includes (raw adc, tdc,
>>>>>> ...)
>>>>>> for all the 1.2 GeV runs, and the first file of all the 5.7 and 6
>>>>>> GeV
>>>>>> runs.
>>>>>>
>>>>>> My first question to Nathan, does the TPCC bank information is good
>>>>>> for this and does it provides raw ADC? (raw ADC are for other tests
>>>>>> later, but we will eventually need them too) Else, what should we
>>>>>> use?
>>>>>>
>>>>>> Then could Lamiaa cook the runs mentionned above? or maybe they can
>>>>>> be
>>>>>> extracted from BOS files from the pass1v1 cooking?
>>>>>>
>>>>>> Best regards,
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Rapha�l Dupr�
>>>>>>
>>>>>
>>>>
>>>
>>>
>>> --
>>> Best regards,
>>> Mohammad Hattawy.
>>>
>>>
>>>
>>>
>>>
>>
>>
>> --
>> Best regards,
>> Mohammad Hattawy.
>>
> _______________________________________________
> Eg6_analysis mailing list
> Eg6_analysis at jlab.org
> https://mailman.jlab.org/mailman/listinfo/eg6_analysis
>