[Halld-tracking-hw] CDC components

[Curtis A. Meyer]

Hi Tim -

  yes, please have them sent directly to us and we will forward some to 
you. That will be
a big help to have them at the end of June.

     curtis
On 6/2/10 2:52 PM, Tim Whitlatch wrote:
> Hi Curtis,
>
> The plastic part samples should be here by June 16. With a quick 
> turnaround, they can have the final parts shipped by the end of June 
> (the entire batch takes 6 days to produce so a partial shipment will 
> not buy us much). We can have them shipped directly to you if that 
> helps? You can send some of the parts to JLAB to look over.
>
> Tim
>
> Curtis A. Meyer wrote:
>> If we would get a partial shipment when they start production, that 
>> would help.
>>
>>   thanks -- Curtis
>> On 6/1/10 1:13 PM, Tim Whitlatch wrote:
>>> Hi Curtis,
>>>
>>> All 3 plastic pieces are run in the same mold. They will make 
>>> samples again in a week or two. We can check them quickly and they 
>>> will run the production quantities. I will be surprised if this can 
>>> all be done before July.
>>> I will call them and see what we can do to speed this up.
>>>
>>> Tim
>>>
>>> Curtis A. Meyer wrote:
>>>> Hi Tim -
>>>>
>>>>    is there any way to speed up the plastic donuts and 
>>>> feedthroughs? They all need to be
>>>> checked before we can start putting straws in and any headway we 
>>>> can make on that
>>>> would be very helpful.  We do not need the pin holders (which we 
>>>> changed), but the other
>>>> two parts (that were fine) would be extremely helpful to get this 
>>>> month.
>>>>
>>>>   thanks --   Curtis
>>>>
>>>>
>>>> On 6/1/10 10:17 AM, Tim Whitlatch wrote:
>>>>> Hi Naomi,
>>>>>
>>>>> We are sending approx. 9000 crimp pins up your way today. We had 
>>>>> received them from Medelec last week.
>>>>> The ones we checked fit the plastic inserts very nicely. A little 
>>>>> hard threading the tungsten wire through, probably need 10x 
>>>>> magnification or something.
>>>>> The plastic components should be your way by Mid July.
>>>>> The next batch of straws should also be your way by July. Maybe we 
>>>>> should send someone to Lamina to check instead of wasting the time 
>>>>> for them to send the samples to the US?
>>>>> The inner skin and support rings should be your way before the end 
>>>>> of this month (June).
>>>>>
>>>>> Cheers,
>>>>>
>>>>>       Tim
>>>>>
>>>>> Naomi Jarvis wrote:
>>>>>> Good morning!
>>>>>>
>>>>>> Our new technician - Amy Woodhall - started work this morning and 
>>>>>> is busy reaming the C endplate holes... we also have 3 students 
>>>>>> here and need to do some forward planning... please could you 
>>>>>> give me a heads up as to when we can expect to see the plastic 
>>>>>> components, next batch of straws and the inner shell?   A rough 
>>>>>> idea (likely month) would be helpful if you do not know more 
>>>>>> exactly, I imagine the plastic cpts should not be too long.
>>>>>>
>>>>>> Thanks,
>>>>>>
>>>>>> Naomi.
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Halld-tracking-hw mailing list
>>>>> Halld-tracking-hw at jlab.org
>>>>> https://mailman.jlab.org/mailman/listinfo/halld-tracking-hw
>>>>
>>>>
>>>> -- 
>>>> Prof. Curtis A. Meyer		Department of Physics
>>>> Phone:	(412) 268-2745		Carnegie Mellon University
>>>> Fax:	(412) 681-0648		Pittsburgh PA 15213-3890
>>>> cmeyer at ernest.phys.cmu.edu	http://www.curtismeyer.com/
>>>>
>>>>    
>>
>>
>> -- 
>> Prof. Curtis A. Meyer		Department of Physics
>> Phone:	(412) 268-2745		Carnegie Mellon University
>> Fax:	(412) 681-0648		Pittsburgh PA 15213-3890
>> cmeyer at ernest.phys.cmu.edu	http://www.curtismeyer.com/
>>
>>    


-- 
Prof. Curtis A. Meyer		Department of Physics
Phone:	(412) 268-2745		Carnegie Mellon University
Fax:	(412) 681-0648		Pittsburgh PA 15213-3890
cmeyer at ernest.phys.cmu.edu	http://www.curtismeyer.com/


-------------- next part --------------
An HTML attachment was scrubbed...
URL: https://mailman.jlab.org/pipermail/halld-tracking-hw/attachments/20100602/cdf75fa6/attachment.html