[Dsg-rich] RICH part drawings to check before fabrication

[Amrit Yegneswaran]

Bob, 


Below are the cost changes as it pertains to colors. 


    * Given that the cost increase for painting the parts yellow is $708 more than having the parts painted in white - 50% the cost of the strongback parts, 
    * and given the fact that we are in a terrible budget crunch, i'm sure you know this fact, there isn't money available to endorse painting the parts in yeloow. 

So the parts will be painted white . 
Thank you for your understanding 


amrit 






White (Current Quote) 	White (Currently quoted) 
	Yellow (If Specified on drawings) 
	Safety Yellow (If Specified on drawings) 

Load Test Parts 
	$1840 
	$2020 
	$2400 

Trolley 
	$2375 
	$2550 
	$3000 

Strongback parts 
	$1490 
	$1843 
	
$2400 

Total Cost 
	$5705 
	$ 6413 
	
$7800 




From: "Robert Miller" <rmiller at jlab.org> 
To: "Tyler Lemon" <tlemon at jlab.org> 
Cc: "dsg-rich" <dsg-rich at jlab.org> 
Sent: Tuesday, August 22, 2017 3:34:40 PM 
Subject: Re: [Dsg-rich] RICH part drawings to check before fabrication 

Hi Tyler, 

You can paint all the parts regular yellow to reduce the cost. 

Regards, 
Bob 

Sent from my iPhone 

On Aug 22, 2017, at 1:59 PM, Tyler Lemon < tlemon at jlab.org > wrote: 




Hello Bob, 

In regards to General Comment #1 you made in the attached document, we were told by G&R Metals that safety yellow is more expensive compared to regular yellow because safety yellow is defined by ANSI Z535 standard. 

Marc has contacted G&R for an estimate on how much more the job will cost if safety yellow is used. The price difference is in the table below. 

White (Current Quote) 	White (Currently quoted) 
	Yellow (If Specified on drawings) 
	Safety Yellow (If Specified on drawings) 

Load Test Parts 
	$1840 
	$2020 
	$2400 

Trolley 
	$2375 
	$2550 
	
$3000 

Strongback parts 
	$1490 
	$1843 
	$2400 

Because of the price difference, could you let us know which parts, if any, can be painted with regular yellow or plain white? 

Best regards, 
Tyler 



From: "Bob Miller" < rmiller at jlab.org > 
To: "Dario Orecchini" < dario.orecchini at googlemail.com >, "Tomassini Sandro" < sandro.tomassini at lnf.infn.it > 
Cc: "Tyler Lemon" < tlemon at jlab.org > 
Sent: Thursday, August 17, 2017 3:01:28 PM 
Subject: Re: RICH part drawings to check before fabrication 



Hi Dario and Sandro, 

Please see my comments in the attached document for the RICH tooling drawings. 

Regards, 

Bob 

On 8/16/2017 3:58 PM, Tyler Lemon wrote: 

BQ_BEGIN

Hello Bob, 

As we discussed on the phone, attached are the three drawings sets for the RICH parts that DSG would like checked by Hall B Engineering. 

It would be urgent to check these as soon as possible to avoid any delay in the parts' fabrication. We expect that the procurement of the fabrication contract will be complete in about one week. 

Best regards, 
Tyler 



-- 
Bob Miller
Hall B Lead Engineer
Jefferson Lab
757 269-7867 


BQ_END

BQ_BEGIN

<RICH Drawing Review.docx> 

BQ_END

_______________________________________________ 
Dsg-rich mailing list 
Dsg-rich at jlab.org 
https://mailman.jlab.org/mailman/listinfo/dsg-rich 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <https://mailman.jlab.org/pipermail/dsg-hallb_rich/attachments/20170822/4d9e617d/attachment-0002.html>