[Dsg-rich] RICH part drawings to check before fabrication

[Dario Orecchini]

Hello,

I and Sandro suggest to use the Yellow RAL 1016. It's a regular Yellow 
very similar to safety Yellow.
Regarding the Bob comments the drawings update is on going, however go 
on with the procurements because
we are speacking of not fundamental details.

Best regards
Dario e Sandro

Il 2017-08-23 00:09 Amrit Yegneswaran ha scritto:
> Bob,
> 
> Below are the cost changes as it pertains to colors.
> 
> 	* Given that the cost increase for painting the parts yellow is $708
> more than having the parts painted in white - 50% the cost of the
> strongback parts,
> 	* and given the fact that we are in a terrible budget crunch, i'm
> sure you know this fact, there isn't money available to endorse
> painting the parts in yeloow.
> 
> _So the parts will be painted white_.
> 
> Thank you for your understanding
> 
> amrit
> 
> 		White (Current Quote)
> White (Currently quoted)
> Yellow (If Specified on drawings)
> 
> Safety Yellow (If Specified on drawings)
> 
> Load Test Parts
> $1840
> $2020
> $2400
> 
> Trolley
> $2375
> $2550
> $3000
> 
> Strongback parts
> $1490
> $1843
> 
> $2400
> 
> TOTAL COST
> $5705
> $ 6413
> 
> $7800
> 
> -------------------------
> 
> FROM: "Robert Miller" <rmiller at jlab.org>
> TO: "Tyler Lemon" <tlemon at jlab.org>
> CC: "dsg-rich" <dsg-rich at jlab.org>
> SENT: Tuesday, August 22, 2017 3:34:40 PM
> SUBJECT: Re: [Dsg-rich] RICH part drawings to check before fabrication
> 
> Hi Tyler,
> 
> You can paint all the parts regular yellow to reduce the cost.
> 
> Regards,
> Bob
> 
> Sent from my iPhone
> 
> On Aug 22, 2017, at 1:59 PM, Tyler Lemon <tlemon at jlab.org> wrote:
> 
>> Hello Bob,
>> 
>> In regards to General Comment #1 you made in the attached document,
>> we were told by G&R Metals that safety yellow is more expensive
>> compared to regular yellow because safety yellow is defined by ANSI
>> Z535 standard.
>> 
>> Marc has contacted G&R for an estimate on how much more the job will
>> cost if safety yellow is used. The price difference is in the table
>> below.
>> 
>> White (Current Quote)
>> White (Currently quoted)
>> Yellow (If Specified on drawings)
>> 
>> Safety Yellow (If Specified on drawings)
>> 
>> Load Test Parts
>> $1840
>> $2020
>> $2400
>> 
>> Trolley
>> $2375
>> $2550
>> 
>> $3000
>> 
>> Strongback parts
>> $1490
>> $1843
>> $2400
>> 
>> Because of the price difference, could you let us know which parts,
>> if any, can be painted with regular yellow or plain white?
>> 
>> Best regards,
>> Tyler
>> 
>> -------------------------
>> 
>> FROM: "Bob Miller" <rmiller at jlab.org>
>> TO: "Dario Orecchini" <dario.orecchini at googlemail.com>, "Tomassini
>> Sandro" <sandro.tomassini at lnf.infn.it>
>> CC: "Tyler Lemon" <tlemon at jlab.org>
>> SENT: Thursday, August 17, 2017 3:01:28 PM
>> SUBJECT: Re: RICH part drawings to check before fabrication
>> 
>> Hi Dario and Sandro,
>> 
>> Please see my comments in the attached document for the RICH tooling
>> drawings.
>> 
>> Regards,
>> 
>> Bob
>> 
>> On 8/16/2017 3:58 PM, Tyler Lemon wrote:
>> 
>>> Hello Bob,
>>> 
>>> As we discussed on the phone, attached are the three drawings sets
>>> for the RICH parts that DSG would like checked by Hall B
>>> Engineering.
>>> 
>>> It would be urgent to check these as soon as possible to avoid any
>>> delay in the parts' fabrication. We expect that the procurement of
>>> the fabrication contract will be complete in about one week.
>>> 
>>> Best regards,
>>> 
>>> Tyler
>> 
>> --
>> Bob Miller
>> Hall B Lead Engineer
>> Jefferson Lab
>> 757 269-7867
> 
>> <RICH Drawing Review.docx>
> 
> _______________________________________________
> Dsg-rich mailing list
> Dsg-rich at jlab.org
> https://mailman.jlab.org/mailman/listinfo/dsg-rich
> 
> _______________________________________________
> Dsg-rich mailing list
> Dsg-rich at jlab.org
> https://mailman.jlab.org/mailman/listinfo/dsg-rich